INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .

23ml Jar of Tamiya XF-1 Black color Acrylic Flat (Matt) Paint.

This is a 5/8oz Tube of Cement for Plastic Models from Testors. For Ages 8 and Up.

This is a 3/4 Oz. Glass Paint Jar with Cover from Badger.

This is a Coarse Grit Sanding Stick from Squadron Products.

This is a Value Pack 7/8oz Tube of Cement for Plastic Models from Testors. For Ages 8 and Up.

This is a 250ml Bottle of Tamiya color Acrylic Paint (Thinner).

This Package Contains an 8 Ounce Assortment of Styrene Pieces (Odds & Ends) for Your Scratch Modeling Needs from Evergreen Scale Models.

Extra-thin plastic model cement with applicator brush. Used to glue parts already held together. The thin glue will wick into the joint for a firm bond.

INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .

This is the Model Master 1/2oz (14.7ml) Gloss High Gloss Clear Enamel Paint from Testors.

23ml Jar of Tamiya XF-2 White color Acrylic Flat (Matt) Paint.

Replacement top that is on all of BSI's non-Pocket CAs.

Excellent Gap-Filling Super-Glue Zap-A-Gap 1 oz bottle from Pacer Glues.

This is a 1/2 oz (14.7mL) glass jar of Flat Black Acrylic Paint from Testors.

180ml Spray Can of Tamiya's Fine Surface Primer L (Gray) for Plastic and Metal.

QUIK-CURE 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE can be handled after 15 minutes. Full strength is reached in 1 hour.

Plastic Model glue with applicator brush.

This is a 6 Meter Roll of 6mm Tamiya Masking Tape Refill.

Wood model glue.

This is a 1/2 Pint Can of Testors Airbrush Thinner.

This is a Tubing Cutter from K&S Engineering.

This is a 1/2 oz (14.7mL) glass jar of Flat White Acrylic Paint from Testors.

This is a 1/2 oz (14.7mL) glass jar of Enamel Olive Drab Paint from Testors.

This is the 200ml Bottle Grey Primer from Vallejo.

180ml Spray Can of Tamiya's Surface Primer L (White) for Plastic and Metal.

This is a 1/4oz (7.5ml) glass jar of Enamel Paint from Testors.

This package includes Five Tubes of 1/8 Round Brass Tubes by K&S Engineering.

MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars.

This is a 1/4 oz (7.5ml) glass jar of Enamel Paint from Testors.

This is a Testors Military Flat Enamel Paint Kit. Used for Decorating and Camouflaging Tanks, Ships, Planes & Figures of Nations.

23ml Jar of Tamiya XF-60 Dark Yellow color Acrylic Flat (Matt) Paint.

23ml Jar of Tamiya XF-16 Aluminum color Acrylic Flat (Matt) Paint.

This is a 1/2 oz (14.7mL) glass jar of Enamel Chrome Silver Paint from Testors.

This patented, revolutionary sanding film is bonded to tough polyester, so it won't crack when crushed or crumpled. Great for the hobbyist.

INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. .

This is a Can of Wet Look Clear One Coat Lacquer Paint from Testors.

23ml Jar of Tamiya X-10 Gun Metal color Acrylic Gloss Paint.

23ml Jar of Tamiya X-11 Chrome Silver color Acrylic Gloss Paint.

This is a 1/2 oz (14.7mL) glass jar of Enamel Semi-Gloss Black Paint from Testors. FEATURES: Made of enamel and is flammable and toxic. Can be used for: Models: Ceramic, Plastic, Leather Household: Stone, Metal, Styrofoam Crafts: Wax, Glass, Paper Figures: Fabric, Wood Not recommended for: vinyl, polyethylene or polypropylene plastics. Excellent for either brush painting or air brushing. Covers well, flows smoothly with no blushing or fading, and can be blended easily. INCLUDES: One 1/2 oz (14.7mL) jar of Enamel Semi-Gloss Black Paint. REQUIRES: Paint Brush or Airbrush to apply to model. Eye, Lung and Skin protection. Enamel Thinner (TESR2148) COMMENTS: Keep out of the reach of children. Hig

INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.

23ml Jar of Tamiya XF-64 Red-Brown color Acrylic Flat (Matt) Paint.

This is the Squadron Tools Drill Bit Index with sizes 61-80 Drill Bits.

This is a Promotional Paint Set from Testors.

This is a 1/2 oz (14.7mL) glass jar of Enamel Light Ghost Gray Paint from Testors.

This is a Testors Aircraft Finishing Enamel Paint Set. Used for Finishing Models of Foreign and Domestic Aircraft.

Supplies that picture-perfect model. The best of everything for building the highest quality models. Great gift for the experienced modeller.

This is a 1/2 oz (14.7mL) glass jar of Enamel Gloss Black Paint from Testors.

23ml Jar of Tamiya XF-63 German Gray color Acrylic Flat (Matt) Paint.