Glues - Page 2

Page 2/20 Glues - Page 2

Extender Tips (24)

Glue Tip Glue Applicator
$4.99 $4.09
Pacer # paapt21
  Add To Cart
Wish List
This is a package of Pacer Extender Tips for CA Glue Bottles.

25g Professional Liquid Cement w/Applicator

Plastic Model Cement
$4.99 $4.09
Revell-Germany # rvl39604
  Add To Cart
Wish List
This is the Revell-Germany 25g Professional Liquid Cement w/Applicator plastic model cement.

QUICK CURE 5 Minute Epoxy (9oz)

Hobby Epoxy
$18.99 $15.59
Hobbylinc # hlc202
  Add To Cart
Wish List
QUIK-CURE 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE can be handled after 15 minutes. Full strength is reached in 1 hour.

Scenic Glue 8 oz

$8.99 $7.09
Woodland # woos190
  Add To Cart
Wish List
A specifically-formulated, high-tack, non-odorous adhesive for applying landscape materials.

MAXI-CURE Extra Thick Cyanoacrylate 1oz

Hobby CA Super Glue
$5.99 $4.99
Hobbylinc # hlc112
  Add To Cart
Wish List
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars.
Deluxe-Materials # dluad77
  Add To Cart
Wish List

Plastic Cement Value Pack (replaces #3509)

Plastic Model Cement
$4.69 $3.69
* currently unavailable
Testors # tes290278
  Pre-Order
Wish List
This is a Value Pack 7/8oz Tube of Cement for Plastic Models from Testors. For Ages 8 and Up.
Website security verified by GoDaddy

INSTA-CURE Gap Filling Cyanoacrylate 1/2oz

Hobby CA Super Glue
$3.99 $3.49
Hobbylinc # hlc106
  Add To Cart
Wish List
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
SALE
31% Off
Hobbylinc # hlc120
  Add To Cart
Wish List
INSTA-FLEX clear rubber toughened has similar qualities to our black IC-2000 but can be used in applications where you do not want the adhesive to be seen. .

Extra Fine Extender Tips (6)

Glue Tip Glue Applicator
$3.99 $3.29
* currently unavailable
Hobbylinc # hlc302
  Pre-Order
Wish List
For use over the standard #312 top, it allows BSI's thin CAs (Insta-Cure, Insta-Flex and Super-Gold) to be applied a drop at a time.

UN-CURE Cyanoacrylate Debonder 1oz

Hobby CA Super Glue Debonder
$3.99 $3.49
Hobbylinc # hlc161
  Add To Cart
Wish List
UN-CURE debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water.

1oz. Liquid Cement w/Applicator (replaces #3507)

Plastic Model and Hobby Cement
$6.54 $4.99
SALE
24% Off
Testors # tes281216
  Add To Cart
Wish List

Super Phatic! Glue

$10.95 $8.69
Deluxe-Materials # dluad21
  Add To Cart
Wish List
SALE
22% Off
Bob-Smith # bsi107
  Add To Cart
Wish List

INSTA-SET Refill Cyanoacrylate 8oz

Hobby CA Super Glue Accelerator
$11.99 $9.19
SALE
23% Off
Hobbylinc # hlc152
  Add To Cart
Wish List
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.

C/A APPLICATOR TOOL

$10.49 $8.29
Flex-I-File # flx805
  Add To Cart
Wish List

SLOW CURE 30 Minute Epoxy (9oz)

Hobby Epoxy
$18.99 $15.59
Hobbylinc # hlc206
  Add To Cart
Wish List
SLOW-CURE 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE can be used for bonding if you're willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE and FINISH-CURE to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours.

MAXI-CURE Extra Thick Cyanoacrylate 1/2oz

Hobby CA Super Glue
$3.99 $3.39
Hobbylinc # hlc111
  Add To Cart
Wish List
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. . Learn about how to Select a Super Glue.

INSTA-CURE Gap Filling CA 8 oz REFILL

Hobby CA Super Glue
$29.99 $24.89
Hobbylinc # hlc109
  Add To Cart
Wish List
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .

Plastic Cement 7/8 oz Carded

Plastic Model Cement
$2.84 $2.29
* currently unavailable
Testors # tes3512
  Pre-Order
Wish List
This is a 7/8oz Tube of Cement for Plastic Models from Testors. For Ages 8 and Up.