INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. New $4.99 (16% off). Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. . Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used pr

INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. New $8.19 (18% off). Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. . Features: INSTA-CURE+ is a gap filling glue that dries in 5-15 sec.

INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. New $8.19 (18% off). Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. . Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered.

MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. New $8.09 (19% off). When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars. Learn about how to Found In : Building Supplies  >  Glues  >  CA Super Glue

MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. New $3.29 (17% off). When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. . Learn about how to Select a Super Glue. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered. INSTA-CURE is a highly refined CA whic

IC-2000 is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. New $7.49 (25% off). The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered. INSTA-CURE is a highly refined CA which, combined with its freshness, gives a guaranteed 2 year shelf life. CAs are reactive monomers that chemically link (polymerize) when pressed into a thin film. The very thin lay

INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. New $3.39 (15% off). Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. . Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered.

MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. New $4.88 (18% off). When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars. Learn about how to Found In : Building Supplies  >  Glues  >  CA Super Glue

INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. New $3.39 (15% off). Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used prop

IC-GEL is an excellent putty for plastic models. New $5.69 (18% off). It will fill any void and can be formed to many shapes. Applying INSTA-SET allows IC-GEL to be sanded or filed to final shape in less than 20 seconds. IC-GEL is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE; IC-Gel, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL can be applied at

INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. New $3.59 (40% off). Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered. I

INSTA-FLEX clear rubber toughened has similar qualities to our black IC-2000 but can be used in applications where you do not want the adhesive to be seen. New $5.99 (33% off). . INSTA-FLEX clear rubber toughened has similar qualities to our black IC-2000 but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000 that gives the CA its black color also contributes to its unsurpassed strength. Since INSTA-FLEX has this carbon removed, its strength is a little less than IC-2000 but still superior to standard CA's. When esthetics are important and a flexible bond is required, INSTA-FLEX is your best choice. It forms superior bonds to soft urethane and vinyl plasti

IC-2000 is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. New $5.59 (20% off). The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered. INSTA-CURE is a highly refined CA which, combined with its freshness, gives a guaranteed 2 year shelf life. CAs are reactive monomers that chemically link (polymerize) when pressed into a thin film. The very thin lay

INSTA-FLEX flexible thin CA is ideal for many applications, including the installation of CA hinges. New $6.69 (33% off). When cured, INSTA-FLEX does not turn brittle and remains clear, even if accelerated with INSTA-SET. It has superior shock resistance. Although not as thin in consistency as INSTA-CURE, INSTA-FLEX still has good penetrating qualities and its application can be easier to control. . For CA hinges, we recommend drilling a 1/16" hole in the center of the hinge slots to insure the complete saturation of the hinge when INSTA-FLEX is applied. INSTA-FLEX has a different, less irritating odor compared to regular CA's, but still can not be used on white foam. INSTA-FLEX has also proven to be superior w

INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. New $16.69 (44% off). Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. . Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used pro

INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. New $24.39 (18% off). Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. . Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered.

MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. New $24.89 (17% off). When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars. Learn about how to Found In : Building Supplies  >  Glues  >  CA Super Glue

SUPER-GOLD and SUPER-GOLD+ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. New $7.39 (17% off). . There are no fumes that irritate the nose and eyes. The SUPER-GOLD's do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF's. They will not fog clear plastic. SUPER-GOLD+ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD + in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET to one piece and apply SUPER

SUPER-GOLD and SUPER-GOLD+ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. New $13.09 (18% off). There are no fumes that irritate the nose and eyes. The SUPER-GOLD's do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF's. They will not fog clear plastic. SUPER-GOLD+ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD + in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET to one piece and apply SUPER-G

SUPER-GOLD and SUPER-GOLD+ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. New $23.49 (21% off). . There are no fumes that irritate the nose and eyes. The SUPER-GOLD's do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF's. They will not fog clear plastic. SUPER-GOLD+ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD + in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET to one piece and apply SUPER