Choose from 50 discount hobbylinc glues up to 33% off from Hobbylinc. Select from the 5 hobbylinc glues categories shown below to narrow your search.
| Showing 1 - 20 of 50 items |
|
|
|
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$4.69
|
| Retail: | $5.99 |
| Savings: | 21% off |
| Product #: | HLC107 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 134
|
$$$$ On Sale $$$$
Sale Price Valid Through Thursday, while quantities last.
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. New $4.69 (21% off). Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Learn about how to Select a Super Glue. |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$8.19
|
| Retail: | $9.99 |
| Savings: | 18% off |
| Product #: | HLC108 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 233
|
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. New $8.19 (18% off). Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Learn about how to Select a Super Glue. |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$4.99
|
| Retail: | $5.99 |
| Savings: | 16% off |
| Product #: | HLC151 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 142
|
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. New $4.99 (16% off). INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET significantly enhances a joint's strength. For difficult to bond materials, INSTA-SET can be applied to one surface and CA to the opposite surface. When brought together, they
|
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$8.19
|
| Retail: | $9.99 |
| Savings: | 18% off |
| Product #: | HLC103 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 233
|
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. New $8.19 (18% off). Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Learn about how to Select a Super Glue. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$8.09
|
| Retail: | $9.99 |
| Savings: | 19% off |
| Product #: | HLC113 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 231
|
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. New $8.09 (19% off). When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars. Learn about how to Found In : Building Supplies > Glues > CA Super Glue |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$3.19
|
| Retail: | $3.99 |
| Savings: | 20% off |
| Product #: | HLC111 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 91
|
$$$$ On Sale $$$$
Sale Price Valid Through Thursday, while quantities last.
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. New $3.19 (20% off). When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. . Learn about how to Select a Super Glue. Features: MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$7.89
|
| Retail: | $9.99 |
| Savings: | 21% off |
| Product #: | HLC118 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 225
|
IC-2000 is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. New $7.89 (21% off). The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000 is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET. When cured, IC-2000 is pliable enough to be carved with a hobby knife. IC-2000 is the best adhesive for R/C car tires. Learn about how to Select a Super Glue. |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$4.38
|
| Retail: | $5.99 |
| Savings: | 26% off |
| Product #: | HLC112 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 125
|
$$$$ On Sale $$$$
Sale Price Valid Through Thursday, while quantities last.
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. New $4.38 (26% off). When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars. Learn about how to Found In : Building Supplies > Glues > CA Super Glue |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$3.39
|
| Retail: | $3.99 |
| Savings: | 15% off |
| Product #: | HLC101 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 97
|
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. New $3.39 (15% off). Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Learn about how to Select a Super Glue. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$3.39
|
| Retail: | $3.99 |
| Savings: | 15% off |
| Product #: | HLC161 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 97
|
UN-CURE debonder will soften cured CA. New $3.39 (15% off). If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water.
|
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$3.39
|
| Retail: | $3.99 |
| Savings: | 15% off |
| Product #: | HLC106 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 97
|
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. New $3.39 (15% off). Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. Learn about how to Select a Super Glue. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$12.79
|
| Retail: | $15.99 |
| Savings: | 20% off |
| Product #: | HLC202 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 365
|
QUIK-CURE 5 min. New $12.79 (20% off). epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE can be handled after 15 minutes. Full strength is reached in 1 hour. If CAs are the cure-all for just about all bonding problems, you may be wondering, "Why do I need epoxy?" One primary reason is price. Epox
|
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$3.99
|
| Retail: | $6.99 |
| Savings: | 42% off |
| Product #: | HLC116 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 114
|
$$$$ On Sale $$$$
Sale Price Valid Through Thursday, while quantities last.
IC-GEL is an excellent putty for plastic models. New $3.99 (42% off). It will fill any void and can be formed to many shapes. Applying INSTA-SET allows IC-GEL to be sanded or filed to final shape in less than 20 seconds. Learn about how to Select a Super Glue. IC-GEL is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE; IC-Gel, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$4.99
|
| Retail: | $5.99 |
| Savings: | 16% off |
| Product #: | HLC102 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 142
|
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. New $4.99 (16% off). Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. Learn about how to Select a Super Glue. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$5.99
|
| Retail: | $8.99 |
| Savings: | 33% off |
| Product #: | HLC120 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 171
|
INSTA-FLEX clear rubber toughened has similar qualities to our black IC-2000 but can be used in applications where you do not want the adhesive to be seen. New $5.99 (33% off). Learn about how to Select a Super Glue. INSTA-FLEX clear rubber toughened has similar qualities to our black IC-2000 but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000 that gives the CA its black color also contributes to its unsurpassed strength. Since INSTA-FLEX has this carbon removed, its strength is a little less than IC-2000 but still superior to standard CA's. When esthetics are important and a flexible bond is required, INSTA-FLEX is yo |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$5.59
|
| Retail: | $6.99 |
| Savings: | 20% off |
| Product #: | HLC117 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 159
|
IC-2000 is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. New $5.59 (20% off). The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000 is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET. When cured, IC-2000 is pliable enough to be carved with a hobby knife. IC-2000 is the best adhesive for R/C car tires. Learn about how to Select a Super Glue. |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$6.69
|
| Retail: | $9.99 |
| Savings: | 33% off |
| Product #: | HLC119 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 191
|
INSTA-FLEX flexible thin CA is ideal for many applications, including the installation of CA hinges. New $6.69 (33% off). When cured, INSTA-FLEX does not turn brittle and remains clear, even if accelerated with INSTA-SET. It has superior shock resistance. Although not as thin in consistency as INSTA-CURE, INSTA-FLEX still has good penetrating qualities and its application can be easier to control. Learn about how to Select a Super Glue. For CA hinges, we recommend drilling a 1/16" hole in the center of the hinge slots to insure the complete saturation of the hinge when INSTA-FLEX is applied. INSTA-FLEX has a different, less irritating odor compared to regular CA's, but still c |
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$24.39
|
| Retail: | $29.99 |
| Savings: | 18% off |
| Product #: | HLC109 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 695
|
New $24.39 (18% off).
|
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$12.79
|
| Retail: | $15.99 |
| Savings: | 20% off |
| Product #: | HLC204 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 365
|
MID-CURE 15 min. New $12.79 (20% off). epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE in most applications. MID-CURE is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength. If CAs are the cure-all for just about all bonding problems, you may be wondering, "Why do I need epoxy?" One primary reason is price. Epoxy costs are about one fourth that of CA. When large objects are being bonded, economics can be a deciding factor on choice of adhesive. The specific characteristics of epoxies also give them advantages in some applications. All ou
|
| [zoom] [Product Info]
|
Vital Information
Updated 5/18/2013
| Your Price: |
$24.39
|
| Retail: | $29.99 |
| Savings: | 18% off |
| Product #: | HLC104 |
| Availability: | Usually ships out in 24 hours |
| Rewards Points: | 695
|
New $24.39 (18% off).
|
|
|
|
|
Rewards Points
* Earn Points for Purchases
* Earn Points for using Hobbylinc
* Use Points for Discounts!
COMPLETE DETAILS
Payment Options
* Purchase Orders also accepted
|
