This is the O.S. Max 1.60 FX High-Performance R/C Engine used for Sport and Aerobatic Aircraft. This 1.60 FX is Designed to use a Muffler or Tuned Pipe.:
Product Specifications
- Displacement: 26.23cc (1.60 cu in):
- RPM range: 1,800 - 10,000 RPM:
- Bore: 33.6mm (1.32):
- Stroke: 29.6mm (1.17):
- Weight: Engine- 1235g (43.6oz) with muffler:
- Muffler: 275g (9.7oz):
- Horsepower: 3.7 PS, 3.65 HP at 9,000 RPM:
- Length: 115.5mm (distance from the backplate screw to drive washer):
- 30mm (distance between centers of the mounting holes):
- Width: 51.5mm (width of engine neglecting engine mounting flanges):
- 62mm (distance between centers of the mounting holes):
- Exhaust mounting screws width (center to center): 42mm (1.65):
- Height: 123.2mm:
- Crankshaft Thread Size: 3/8-24:
- Crankshaft Length (drive washer front to crankshaft front): 42mm:
- Crankshaft Threaded Area: 28mm:
- Suggested Props: Aerobatic: 15x12-14, 16x10-14, 16.5x10-13:
- Sport: 17x10-13, 18x10-12:
What's Included
- One Assembled 1.60 FX Ringed R/C Airplane Engine, #60F Carb, smaller nut for APC props and 3/8-24 safety lock nut
- One exhaust adaptor:
- One remote needle valve:
- One 77mm (3) clear fuel tubing for remote needle:
- Two 5 x 15mm cap head adapter mounting screws:
- Two 5 x 19mm cap head muffler mounting screws:
- One 4mm allen wrench:
- One expansion style muffler (E-5010) with screws:
- One illustrated instructions booklet w/parts list and O.S. decal:
- One O.S. #8 glow plug (osmg2691):
Required
- Fuel with 18% (minimum) lubricant content and 5% to 25% Nitromethane (Can be flown on FAI fuel, which is 0% Nitro)
|
Click a link to the left to view products here... |
Product Rankings Manufacturer Comments - Needle Settings: High Speed: 2 - 2.5 turns out from fully closed Low Speed: .75 turns out from fully closed with the throttle fully closed:
- Recommended is a 450-550cc fuel tank which allows approximatel 10 to 12 minute flights..:
- Locate the fuel tank so that the top of the tank is 5-10mm (1/4-3/8 above the level of the needle valve..:
- A 1/16 wire (not included) can be used to extend the needle valve b inserting the wire into the pre-drilled hole on the end of needl valve and tightening it in place with the supplied set screw..:
- Remote needle valve is held in place by a nut instead of screws..:
- To use a Tru Turn spinner and an APC propeller, modeler will nee the Tru Turn jam nut set TT-0378-A (not carried at this time)..:
|
Also Viewed
16x10 3-Blade Prop
$9.99 [ 36% off ]
.91HZ-R 3C Speed Red 61G
$424.98 [ 46% off ]
DLE-222cc 4-Cyl Gas Engine w/EI/Mufflers/Mount
$1784.99 [ 10% off ]
.25FX ABL 20D Carb 892 Muffler
$129.99 [ 35% off ]
.91HZ-R 3D Speed Black 61G
$424.98 [ 46% off ]
Alien Chaser Model Rocket Kit
$5.39 [ 29% off ]
1/48 AH-1S Attack Cobra
$10.79 [ 29% off ]
TRX 2.5R Racing Engine w/PS
$101.79 [ 40% off ]
18MZH 2.4G R7008SB Heli Bi-Directional Mode 2
$2999.99 [ 25% off ]
C6-5 Model Rocket Engine (3)
$7.89 [ 33% off ]
Wadding Pro Series II
$6.69 [ 33% off ]
F40-7W Reload Kit 29/40-120
$9.39 [ 32% off ]
G-3250 Engine Dual BB Schnuerle Giant Scale
$199.98 [ 50% off ]
B4-4 Model Rocket Engine (3)
$7.19 [ 33% off ]
BT-60 Tube Coupler
$0.89 [ 25% off ]
Optic Sport 2.4 Micro 4x HS-325BB Optima 6
$188.19 [ 41% off ]
BT-80 Tube Coupler
$0.99 [ 28% off ]
.50SX-H Hyper Ring 60LH Carb
$199.98 [ 42% off ]
BT-80 15'' Body Tube
$1.49 [ 57% off ]
E9-6 Model Rocket Engine (3)
$15.99 [ 33% off ]
|
|
|
|
;postJson('/cgi-bin/a4.cgi','aform');)
