Plastic Models

Accurately reproduced M113A3 acted in Gulf War and Iraqi War Hightly detailed interior of the A3 version Rear door can be positioned open and closed Various interior/exterior parts, accessories & storage racks Waterslide decals Illustrated asse guide. One plastic model. This is the 1/35 Scale M113A3 ''Iraq 2003'' Plastic Model Kit from Academy. Suitable for Ages 10 & .....
...more about the Academy Plastics 1/35 M113/A3 OIF

Fully reproduced rivets innumerably covered in the hull Reproduced early version of VVSS (Vertical Volute Spring Suspention) Accurately reconstructed 75mm main gun mounted on the upper hull and Royal Army type 37mm turret Waterslide decals for 2 versions 1) Royal Army, North Africa, 1943 2) Royal Army, 8th Army, El Alamein 1942 Illustrated assembly guide. One plastic model. This is the 1/35 Scale M3 Grant Plastic Model Kit from Academy. Suitable for Ages 10 & .....
...more about the Academy Plastics 1/35 M3 Grant

In 1951, a contract was granted to Ford Motor Co. to develop a Military Utility Tactical Truck. The vehicles were issued to the military with the designation of M151. Due to the swing-axle type suspension and lack of body tilt on cornering, the M151 had a tendency to oversteer and roll when cornered too aggressively. Despite a reputation of being unsafe, the M151 established a record of reliability and proven performance over a wide range of operational areas, suited for .....
...more about the Academy Plastics 1/35 M151A1 Light Utility Truck

The Panzer IV, in its many versions, was one of the most widely used German tanks of WWII. The Panzer IV was powered by a Maybach V-12 engine which provided over 300hp and was connected to the drive sprockets via a 6-speed transmission. The H-model of this tank was introduced in 1943 and featured thicker armour to provide better protection against the Soviet T-34/85's and JS-II's. Highly detailed 1/35th scale plastic kit for static display. 257 parts in tan plastic and .....
...more about the Academy Plastics 1/35 Pz Kpfw IV Ausf.H4

The Panzer IV, in its many versions, was one of the most widely used German tanks of WWII. The Panzer IV was powered by a Maybach V-12 engine which provided over 300hp and was connected to the drive sprockets via a 6-speed transmission. The H-model of this tank was introduced in 1943 and featured thicker armour to provide better protection against the Soviet T-34/85's and JS-II's. Highly detailed 1/35th scale plastic kit for static display. 257 parts in tan plastic and .....
...more about the Academy Plastics 1/35 Pz Kpfw IV Ausf.H

The Sturmgeschutz IV was an assault gun produced for the German Army based on the Panzer IV chassis. It was used mainly as a mobile artillery piece to knock out hardened enemy emplacements such as pill-boxes, anti-tank guns and other obstacles. The guns were used throughout WWII and served on the Russian front, plus the battles around Normandy after D-Day. Detailed 1/35th scale plastic kit for static display. 214 parts in medium tan plastic with one piece flexible P.V.C. .....
...more about the Academy Plastics 1/35 Sturmgeschultz IV

The Panzer IV, in its many versions, was one of the most widely used German tanks of WWII. The Panzer IV was powered by a Maybach V-12 engine which provided over 300hp and was connected to the drive sprockets via a 6-speed transmission. The Flakpanzer IV Wirbelwind was a Panzer IV chassis with a new turret containing a 4 barrel anti-aircraft gun. The Wirbelwind was used to protect infantry and vehicles against air attack. Highly detailed 1/35th scale plastic kit for static .....
...more about the Academy Plastics 1/35 Flakpanzer IV Wirbelwind Quad 20mm Tank

Great Gift Idea
The M2 Bradley is one of the newest additions to the inventory of the U.S. Army and was used with great success during Operation Desert Storm in 1991. The Bradley is an armoured personnel carrier equipped with a turret mounted cannon, effective against enemy troops and lightly armoured vehicles. Highly detailed 1/35th scale plastic kit for static display. 285 parts in tan plastic with flexible P.V.C. tracks. Detailed chassis with individual suspension arms and road wheels. .....
...more about the Academy Plastics 1/35 M2 Bradley IFV

This vehicle set accurately depicts items that would be found in use on a WWII German airfield; - Opel Blitz fuel truck - Schwimmwagen - Bomb cart The fuel truck is highly detailed with positional doors on both the front and back of the tank. Impressively detailed Schwimmwagen. Nicely detailed bomb cart and 8 jerry cans. Waterslide decals. Illustrated assembly guide. (1) Fuel Truck. (1) Schwimmwagen. (1) Bomb Cart. Assemble a German Fuel Truck & Schwimmwagen with this .....
...more about the Academy Plastics 1/72 WWII German Fuel Truck & Schwimmwagen

Static display reproduction of the hardtop cabin version. Highly detailed chassis. Realistically detailed cargo bed. Separate cargo load of fuel drums, ammo boxes, and jerry cans. Nicely detailed.30 na d.50 caliber machine guns. Detailed engine and cab interior. Waterslide decals for 2 US Army vehicles in NW Europe, WWII. Illustrated assembly guide. One Plastic Model. Assemble a U.S. WWII 2 Ton 6x6 Cargo Truck with this Plastic WWII Ground Vehicle Model Kit from Academy. .....
...more about the Academy Plastics 1/72 US 1/2 Ton Cargo Truck 6x6

Historically accurate static display model. Highly detailed engine and undercarriage. Authentic rubber tires. Model with either mounted launcher or tripod. One realistic driver figure. Clear plastic windshield, headlights and tailights. Includes detailed jerry can, ax and other accessories. Waterslide decals with markings for the U. S. Marine version of the M151A2. Includes multilingual, pictoral instruction booklet. (1) Plastic Model. Build a M151A2 TOW Missile Launcher .....
...more about the Academy Plastics 1/35 M151A2 TOW Missile Launcher

This WWII Ground Vehicle Set 6 contains the parts to build the following 3 models; M3 Half Track 1/4 Ton Amphibian Vehicle Military Motorcycle Stunning model replicas engineered with exquisite surface detail! Slide molds create beautifully reproduced chassis and tracks. Superb interior details. Exquisitely detailed military motorcycle. Realistically molded Jerry cans. Waterslide decals. Illustrated assembly guide. (3) Plastic Models. This is a M3 Half Track & 1/4 Ton .....
...more about the Academy Plastics 1/72 M3 Half Track w/Amphibian

Highly detatiled kit Authentic reproduction of M25 Tracot and M15 Semi-Trailer Allied best known heavy Armored Vehicle Carrier of WWII Meticulous interior cabin detailing Accurate re-creation of suspension and tires Waterslide decals Illustrated assembly guide. One Plastic Models. This is the 1/72 US Tank Transporter Dragon Wagon Plastic Model Kit from MRC/Academy. Suitable for Ages 10 & .....
...more about the Academy Plastics 1/72 M26 Dragon Wagon

Accurately reproduction of cargo truck used by US Armed Forces and Alliances Accurate re-creation of suspension and tires Meticulous interior cabin detailing Waterslide decals for two versions; 1) Baghdad Iraq, 2003 2) Vietnam, 1968 Illustrated assembly guide. One plastic model. This is the 1/72 Scale US M35 2.5ton Cargo Truck Plastic Model Kit from the Academy Ground Vehicle Set-8. Suitable for Ages 10 & .....
...more about the Academy Plastics 1/72 M35 2.5Ton Cargo Truck

...more about the Academy Plastics 1/72 M1126 Stryker

Frequently described as the most advanced tank in the world, the M1A1 Abrams is unique in that it is powered by turbine instead of diesel engines. The tank has excellent armour protection and is also able to fire at and hit targets while moving, due to its stabilized gun mount. The M1A1 is improved over the original M1 and features a new 120mm main gun, increased frontal armour, and improved environmental controls. Detailed 1/35th scale plastic kit for static display. 172 .....
...more about the Academy Plastics 1/35 M1A1 Abrams

The German Tiger tank was one of the most powerful tanks in WWII and was greatly feared and respected by the Allies because of its 88mm main gun and thick armour plate. Tiger production began in 1942 and the tank remained in production with minor modifications through the end of WWII. Typically, Tigers had a crew of five. They could travel at up to 23mph on hard roads and were powered by Maybach 21,353cc V-12 engines that developed 642hp. Detailed 1/35th scale plastic kit .....
...more about the Academy Plastics 1/35 Tiger I WWII Tank

The M-113 APC was developed for the U.S. Army in the late fifties and since then has seen use by the armies of over 50 countries. The M113 is a fairly small vehicle, yet it can carry a squad of ten soldiers and is amphibious. It proved especially useful in Southeast Asia where it could easily travel through waterlogged jungles. The standard armament of the M113 is a single.50cal machine gun - subject to many field upgrades. Highly detailed 1/35th scale plastic kit for .....
...more about the Academy Plastics 1/35 M113A2 Weapons Carrier

Named after one of the most famous American generals of WWII, the M47 Patton entered service at the tail end of the Korean war. It was equipped with a number of innovative features including a stabilized 90mm gun and an increasd rate of fire over the M46 and older tank designs. The M48 version featured even more improvements and was widely exported. Many countries continue to use the Patton as their main battle tank. Among these is Korea which has added night vision systems .....
...more about the Academy Plastics 1/35 M48A5 Patton

The M163 Vulcan is a development of the M113 armoured personnel carrier. The vehicle is equipped with a turret that contains the 6 barrel 20mm Vulcan rotary gun which can fire up to 1000 to 3000 rounds per minute. The gun is aimed and fired with aU.S. Navy Mk20 Model 0 lead-computing sight and range-only radar. Specialized anti-aircraft vehicle. Highly detailed 1/35th scale plastic kit for static display. 472 parts in light green & dark grey plastic. Elevating and .....
...more about the Academy Plastics 1/35 M163 Vulcan

Designed specifically for 1/35 scale plastic German Tiger I and Sturm Tiger tank models. Replaces the single piece flexible PVC tracks that come with most armour models in this scale. Made up of individual links, just like real treads, so they canbe positioned around the tanks wheels much more realistically. 208 individual tread blocks - enough for one tank model, plus spares. Instructions for assembly are printed on the packaging. One Set of Individual Tank Tread Blocks .....
...more about the Academy Plastics 1/35 Tiger I Treads

Named after one of the most famous American generals of WWII, the Patton entered service at the tail end of the Korean war. Over the years, improved versions culminated in the M48, and the M60A1 was developed from it to counter the Russian T-54, which featured a 105mm main gun, along with a much improved rangefinder system. The Israeli Army was the first to install a passive explosive reactive armour system on the M60A1. The passive armour blocks explode to destroy or .....
...more about the Academy Plastics 1/35 M60A1 Blazer w/KMT-4

The Sherman tank was the most widely used allied tank of WWII. The M4A1 was an improved version introduced in 1944 and carried a 76mm main gun. In 1956, France delivered 100 M4A1's to Israel who upgraded them substantially. Eventually, even the upgraded Shermans were outclassed by newer Soviet tank models and the Israeli's again improved the basic M4A1 to create the M51 Super Sherman. This tank featured a 105mm gun, a new 460hp Cummins diesel engine, and modifications to .....
...more about the Academy Plastics 1/35 M51 Super Sherman Israel

The M18 Hellcat is not really considered a tank, but is designated as a gun motor carriage. This means it is mobile artillery intended more for infantry support. The M18 was used primarily during WWII. It was quite fast for a tracked vehicle, witha top speed of 55mph. It was powered by a 9-cylinder radial engine producing 340 or 400hp. A total of 2,507 M18's were produced between July 1943 and March 1945. Highly detailed 1/35th scale plastic kit for static display. 378 .....
...more about the Academy Plastics 1/35 M18 Hellcat U.S. Army

The German Tiger tank was one of the most powerful tanks to see use in WWII and was greatly feared and respected by the Allies because of its 88mm main gun and thick armour plate. Tiger production began in 1942 and the tank remained in production with minor modifications through the end of WWII. Typically, Tigers had a crew of 5. They could travel at up to 23mph on hard roads and were powered by Maybach 21,353cc V-12 engines that delivered 642hp. Detailed 1/35th scale .....
...more about the Academy Plastics 1/35 Tiger I Exterior Mdl

The German Tiger tank was one of the most powerful tanks to see use in WWII and was greatly feared and respected by the Allies because of its 88mm main gun and thick armour plate. Tiger production began in 1942 and the tank remained in production with minor modifications through the end of WWII. Typically, Tigers had a crew of 5. They could travel at up to 23mph on hard roads and were powered by Maybach 21,353cc V-12 engines that delivered 642hp. Detailed 1/35th scale .....
...more about the Academy Plastics 1/35 Tiger I w/Interior

The M-113 APC was developed for the U.S. Army in the late fifties and since then has seen use by the armies of over 50 countries. The M113 is a fairly small vehicle, yet it can carry a squad of 10 soldiers and is amphibious. It proved especially useful in Southeast Asia where it could easily travel through waterlogged jungles. The standard armament of the M113 is a single.50cal machine gun - subject to many field upgrades!. Highly detailed 1/35th scale plastic kit for .....
...more about the Academy Plastics 1/35 M113A1 APC Vietnam

Named after one of the most famous American generals of WWII, the Patton entered service at the tail end of the Korean war. Over the years, improved versions culminated in the M48; the M60A1 was developed from the M48 to counter the Russian T-54 and featured a 105mm main gun along with a much improved rangefinder system. The latest upgrade to U.S. Marine Corps, Patton is a passive explosive reactive armour system. The passive armour blocks explode to destroy or deflect .....
...more about the Academy Plastics 1/35 M60A1 Patton Tank w/Dozer Blade

The Israeli Defense Force (IDF) created the Markava series of tanks out of the need to have an independent source of Main Battle Tanks (MBT). The armor is modular for quick replacement and features spacing that helps lessen the effect of anti-tankweapons. The tank is also equipped with an environmental control system that protects the crew from chemical weapons. The Merkava is equipped with impressive weaponry and has proved to be a very effective craft. Plastic pieces .....
...more about the Academy Plastics 1/35 IDF Merkava MK III

Plastic pieces are molded in dark green and attached to sprue trees. Accurately reproduced hull, 76mm gun and interior details. Moveable gun elevation and suspension. Extensive accessory detail parts. Choice of open or closed hatches. Realistic flexible tracks. Waterslide decals. Detailed pictorial instructions. One 1/35 Scale U.S. Tank Destroyer M-10 Gun Motor Carriage Plastic. Model Kit. This is a 1/35 Scale U.S. Tank Destroyer M-10 Gun Motor Carriage Plastic Model Kit .....
...more about the Academy Plastics 1/35 U.S. M-10 Tank Destroyer