Great-Planes Plastic Models

Two aluminum end plates. Two large plywood hold down pieces. Two small plywood hold down pieces. Two 1/4'' wing jig rods. Two wing nuts. Four #8 x 1/2'' wood screws. Two 6-32 bolts. One 1/2'' wood center brace. Two 1/2'' wood base pieces. One instruction booklet. The Wing Jig holds wing ribs in perfect alignment during construction. It will accomodate a 34'' panel to build up to a 68'' tapered wing. Constant chord wings can be built to any size. All hardware is included. .....
...more about the Great Planes Wing Jig Kit

Multiple-section, finger-jointed wood construction resists warping, so modelers can build with greater confidence. Fine wood grain surface and uniform density accepts T-pins easily. Parts are T-pinned in place over the plans on top of the board, so the airplane structure can be built and then glued once the parts are in position. This board is designed for small projects. One Small size 12x24x3/4 Pro Building Board. This is a Small size 12x24x3/4 Pro Building Board from .....
...more about the Great Planes Pro Building Board 12x24x3/4''

Multiple-section, finger-jointed wood construction resists warping, so modelers can build with greater confidence. Fine wood grain surface and uniform density accepts T-pins easily. Parts are T-pinned in place over the plans on top of the board, so the airplane structure can be built and then glued once the parts are in position. This board is designed for planes up to. 40 size models. One Medium size 16x36x3/4'' Pro Building Board. This is a Medium size 16x36x3/4'' Pro .....
...more about the Great Planes Pro Building Board 16x36x3/4''

Multiple-section, finger-jointed wood construction resists warping, so modelers can build with greater confidence. Fine wood grain surface and uniform density accepts T-pins easily. Parts are T-pinned in place over the plans on top of the board, so the airplane structure can be built and then glued once the parts are in position. This board is designed for large assembly projects. One Large size 16x48x3/4'' Pro Building Board. This is a Large size 16x48x3/4'' Pro Building .....
...more about the Great Planes Composite Building Board 16x48x3/4''

Direct Replacement Part. Used For Holding Down All Of The Different Accessories To The Building Board. Ten Magnets. Twenty Steel Plates. These Magnets Are Used With The Magic Magnet Building Board .....
...more about the Great Planes Magic Magnets

Perfect for working on small projects in tight places. Constructed of durable.055'' aluminum (innovative contour shape). Sanding surface stays flat to +/-.008'' (perfect for balsa sheeted wings). Sander sands smoothly and accurately with great results every time. One Easy Touch Hand Sander. One Sheet 80 grit 2-1/4'' x 5.5'' Adhesive Backed Sandpaper. One Sheet 150 grit 2-1/4'' x 5.5'' Adhesive Backed Sandpaper. One Sheet 220 grit 2-1/4'' x 5.5'' Adhesive Backed Sandpaper. .....
...more about the Great Planes Easy-Touch Hand Sander 5.5''

Perfect for working on small projects in tight places. Constructed of durable.055'' aluminum (innovative contour shape). Sanding surface stays flat to +/-.008'' (perfect for balsa sheeted wings). Sander sands smoothly and accurately with great results every time. One Easy Touch Hand Sander. The Easy-Touch Hand Sander is the ideal sanding tool for home and hobby .....
...more about the Great Planes Easy-Touch Bar Sander 11''

Perfect for working on small projects in tight places. Constructed of durable.055'' aluminum (innovative contour shape). Sanding surface stays flat to +/-.008'' (perfect for balsa sheeted wings). Sander sands smoothly and accurately with great results every time. One Easy Touch Hand Sander. The Easy-Touch Hand Sander is the ideal sanding tool for home and hobby .....
...more about the Great Planes Easy-Touch Bar Sander 22''

Perfect for working on small projects in tight places. Constructed of durable.055'' aluminum (innovative contour shape). Sanding surface stays flat to +/-.008'' (perfect for balsa sheeted wings). Sander sands smoothly and accurately with great results every time. One Easy Touch Hand Sander. The Easy-Touch Hand Sander is the ideal sanding tool for home and hobby .....
...more about the Great Planes Easy-Touch Bar Sander 33''

Perfect for working on small projects in tight places. Constructed of durable.055'' aluminum (innovative contour shape). Sanding surface stays flat to +/-.008'' (perfect for balsa sheeted wings). Sander sands smoothly and accurately with great results every time. One Easy Touch Hand Sander. The Easy-Touch Hand Sander is the ideal sanding tool for home and hobby .....
...more about the Great Planes Easy-Touch Bar Sander 44''

One 12' roll of 80 grit self-adhesive sandpaper. This is the sandpaper designed for the Great Planes ''Easy-Touch'' sander .....
...more about the Great Planes Easy-Touch Sandpaper 80 Grit

One 12' roll of 150 grit self-adhesive sandpaper. This is the sandpaper designed for the Great Planes ''Easy-Touch'' sander .....
...more about the Great Planes Easy-Touch Sand Paper 150 Grit

One 12' roll of 180 grit self-adhesive sandpaper. This is the sandpaper designed for the Great Planes ''Easy-Touch'' sander .....
...more about the Great Planes Easy-Touch Sand Paper 180 Grit

One 12' roll of 220 grit self-adhesive sandpaper. This is the sandpaper designed for the Great Planes ''Easy-Touch'' sander .....
...more about the Great Planes Easy-Touch Sand Paper 220 Grit

Designed to be used with the Easy-Touch Hand Sander (GPMR6169). Sandpaper Assortment. Two #80 Grit. Two #150 Grit. Two #220 Grit. This package contains 6 adhesive-backed Sandpaper sheets. Great for the R/C modeler or .....
...more about the Great Planes Easy-Touch Sandpaper Asst 2.25x5.5''

A large gripping surface for the whole hand to help eliminate fatigue Constructed of. 055'' aluminum One thick leading edge countour. 95'' One thinner or trailing edge countour. 38'' One ''V'' shaped contour 1'' (tip to tip) x. 35'' tall. One countoured sander. This is the GREAT PLANES EASY TOUCH COUNTOUR SANDER, it has three pre-shaped sanding surfaces built into it. Sand paper is fit into the different contours to give some of the most common control surface shapes, this .....
...more about the Great Planes Easy-Touch Contour Multi Sander 11''

A large gripping surface for the whole hand to help eliminate fatigue. Constructed of.055'' aluminum. One thick rounded leading edge countour .95''. One rounded thinner or trailing edge countour .38''. One ''V'' shaped contour 1'' (tip to tip) x.35'' tall. One countour sander. This is the GREAT PLANES EASY TOUCH COUNTOUR SANDER that has three pre-shaped sanding surfaces built into it. Sandpaper is fit into the different contours to give some of the most common control .....
...more about the Great Planes Easy-Touch Multi-Sander 22''

Convenient All-In-One Package Eliminates Guesswork. Great for beginners or advanced modelers, having the Easy Touch Sander and Sandpaper to sand flat surfaces on an airplane. High Quality Great Planes Accessories. One Great Planes Easy Touch 11'' Sander (GPMR6170). One Roll of 150 grit Great Planes Sandpaper (GPMR6183). One Roll of 220 grit Great Planes Sandpaper (GPMR6185). This is a Easy Touch / Sandpaper, All-In-One-Gift .....
...more about the Great Planes Easy-Touch/Sandpaper Gift Pack

This tool cuts perfect grooves in balsa for installing elevator joiner wires, aileron torque rods and bearings, tailgear wires and bearings, or to clean pushrod exits in fuselages. Creates crisp, clean grooves in balsa by using a back and forth twisting motion. Creates a uniformly round groove that increases the rod's performance - without the need for sanding. Much safer than using a hobby knife or drill to gouge out the wood. One Groove Tube Cutting Tool (in a storage .....
...more about the Great Planes Groove Tube-Grooving Tool

Great Planes Dead Center Hole Locater is a tool that should be in every modelers toolbox. The tool is extremely easy to use. Simply press its self- centering alignment cone into the mounting hole with the engine positioned on the motor mount, and give the handle a few turns, the sharp drill tip leaves perfectly centered marks every time!. One dead center hole locating tool, with drill size guide on back of package. One clear protective plastic tube. This is a Dead Center .....
...more about the Great Planes Dead Center Hole Locator

Contains everything you need to successfully build wooden ship models. Assortment of top-quality items. One Great Planes Easy-Touch 5.5'' (140mm) Hand Sander. One 80-grit Sandpaper. One 150-grit Sandpaper. One 220-grit Sandpaper. One #1 Hobby Knife Handle. Five #11 Hobby Knife Blades. One Hobbico Pin Vise with six assorted drill bits inside. One 2 oz (56.7g) bottle of Great Planes Pro Wood Glue. One.5 oz (14.2g) bottle of Great Planes Pro CA+ Glue. One CA Glue Applicator .....
...more about the Great Planes Ship Builder's Tool Kit

Heavy-duty, all metal construction (black in color). Rubber comfort grip reduces hand fatique (red in color). Alignment pin puts the Z-bend exactly where you want it - everytime. (see COMMENTS) Makes Z-bends in line with the pushrod even in limited space installations. Makes 90 degree Z-bends in wire up to 1/16'' in diameter. One year quality guarantee. One set of Precision Z-Bend Pliers with Navigator Alignment Pin. This is the Precision Z-Bend Pliers with Navigator .....
...more about the Great Planes Precision Z-Bend Pliers

Hardened, heat-treated steel shanks for high torque. Ball end engages the sockets fully, even at angles up to 25 degrees. Small versions have a metal insert on the shaft to prevent stripping of the handle. Size is stamped into the yellow handle for easy reference. One.050'' Ballwrench. This is a.050'' Ballwrench from Great .....
...more about the Great Planes Standard Ball Wrench .050''

Hardened, heat-treated steel shanks for high torque. Ball end engages the sockets fully, even at angles up to 25 degrees. Small versions have a metal insert on the shaft to prevent stripping of the handle. Size is stamped into the yellow handle for easy reference. One 5/64'' Ballwrench. This is a 5/64'' Ballwrench from Great .....
...more about the Great Planes Standard Ball Wrench 5/64''

Hardened, heat-treated steel shanks for high torque. Ball end engages the sockets fully, even at angles up to 25 degrees. Small versions have a metal insert on the shaft to prevent stripping of the handle. Size is stamped into the yellow handle for easy reference. One 3/32'' Ballwrench. This is a 3/32'' Ballwrench from Great .....
...more about the Great Planes Standard Ball Wrench 3/32''

Hardened, heat-treated steel shanks for high torque. Ball end engages the sockets fully, even at angles up to 25 degrees. Small versions have a metal insert on the shaft to prevent stripping of the handle. Size is stamped into the yellow handle for easy reference. One 7/64'' Ballwrench. This is a 7/64'' Ballwrench from Great .....
...more about the Great Planes Standard Ball Wrench 7/64''

Hardened, heat-treated steel shanks for high torque. Ball end engages the sockets fully, even at angles up to 25 degrees. Small versions have a metal insert on the shaft to prevent stripping of the handle. Size is stamped into the yellow handle for easy reference. One 9x64'' Ballwrench. This is a 9/64'' Ballwrench from Great .....
...more about the Great Planes Standard Ball Wrench 9/64''

Hardened, heat-treated steel shanks for high torque. Ball end engages the sockets fully, even at angles up to 25 degrees. Small versions have a metal insert on the shaft to prevent stripping of the handle. Size is stamped into the yellow handle for easy reference. One 5/32'' Ballwrench. This is a 5/32'' Ballwrench from Great .....
...more about the Great Planes Standard Ball Wrench 5/32''

Hardened, heat-treated steel shanks for high torque. Ball end engages the sockets fully, even at angles up to 25 degrees. Small versions have a metal insert on the shaft to prevent stripping of the handle. Size is stamped into the yellow handle for easy reference. One 1/16'' Ballwrench. This is a 1/16'' Ballwrench from Great .....
...more about the Great Planes Standard Ball Wrench 1/16''

Hardened, heat-treated steel shanks for high torque. Ball end engages the sockets fully, even at angles up to 25 degrees. Small versions have a metal insert on the shaft to prevent stripping of the handle. Size is stamped into the yellow handle for easy reference. One.050'' Ballwrench. One 1/16'' Ballwrench. One 5/64'' Ballwrench. One 3/32'' Ballwrench. One 7/64'' Ballwrench. One 9/64'' Ballwrench. This is a Sandard 6-piece Ballwrench Set from Great .....
...more about the Great Planes 6pc Standard Ballwrench Set