Model Trains

Features: For improved conductivity and engine performance, keep your track and wheels clean with Aristo-Craft Track Cleaner. It also doubles as smoke fluid, for the cleanest smoke around without the buildup.
...more about the Crest Crest Smoke Fluid & Track Cleaner -- 4oz

Features: Add extra conductivity and smooth operation to locomotives by adding to axle bearings and bushings.
...more about the Crest Crest Lube Conductive

Features: Works for both G and HO Scales. Supplies 22V DC at 13 amps for G Scale or 13.8V DC at 20 amps for HO Scale.
...more about the Crest Power Supply -- Switching D.C./22v DC,13Amp G Scale,13.8v DC,20 amps for HO scale

Features: * The Train Engineer walk-around wireless control system is ideally suited for backyard garden railroads and can be used for DC indoor/outdoor railroads of any size or gauge. * No modification to the locomotive is required. It use a 27 MGHZ multidirectional FM signal with Pulse Code Modification (P.C.M.) that eliminates any outside signal interference. It operates off of your normal power pack: just connect the receiver unit into existing wiring between the track layout and your power supply. * The Train Engineer gives you wireless control of your train within a 300-foot circle of the receiver unit and maintains all the functions of your power pack while enhancin
...more about the Crest Train Engineer Walk Around 2 Piece Set -- Includes #55471 Receiver & #55473 Transmitter/10 amp rating (2)

Features: Additional transmitter for the original Train Engineer. 27 Megahertz.
...more about the Crest Train Engineer Transmitter

Features: Simplified version of Train Engineer. A wireless radio control system for all DC electric trains. Includes one transmitter and one receiver.
...more about the Crest Basic Train Engineer -- 2 AMP 100'

Features: Increases airflow to keep interior components of Receiver (#227-55471; also included with #55470, both sold separately) cooler.
...more about the Crest Fan for 55471 -- Above 5 Amps

Features: * Now you can see what your railroad looks like from the engineer's point of view! With a camera slightly larger than the diameter of a quarter and only 3/4" deep, you can ride along with just about any loco. The camera broadcasts to the included receiver which is connected to a TV or VCR and you can watch all the action as if you were in the cab yourself. * System includes camera, microphone enclosed within camera case, receiver, 9V battery connector, a 36" two-wire A/V cable for easy positioning of receiver, 9V DC transformer for receiver and an 8V DC transformer for the camera.
...more about the Crest Video -- Train Remote View Camera System

Features: * Thus edition of the Train Engineer system eliminates the worry of clean track. Signal is transmitted via airwaves instead of through the track so it can run on battery or track power. Sound, all lighting functions and more can be operated from the handheld transmitter. Control up to 999 trains and accessories with one transmitter and identify every locomotive by both description and roadnumber. Innovative throttle allows easy and accurate operation. A graphic display walks you through all functions and a detailed manual is also included. * Includes receiver and handheld transmitter.
...more about the Crest Revolution Train Engineer 2.4 GHz -- For Large Scale Trains

Features: Scale size housing, easily mounted on any freight car. High-intensity LED slowly flashes a bright light rearward. Requires 3V input, easily obtained from two small batteries; the TP-1 Track Power (#800-2001), can be used if the car is equipped with track power pickups.
...more about the Circuitron End-Of-Train Flasher -- Red Light

Features: Alternately flashes two 1.7mm diameter, high-intensity, lens-end lamps (included) at a slow rate to simulate ditch lamps. With the addition of a DPST or DPDT switch, the DL-1 circuit can be bypassed so the lights stay on. Requires 2.4-3V DC input from batteries, TP-2 #800-2002 or TP-3.
...more about the Circuitron DL-1 Oscillating Ditch Lights

Features: Simple, inexpensive circuits for flashing LEDs or lamps (sold separately).
...more about the Circuitron Basic Flasher for LED's - HO-Scale

Features: Miniature voltage regulator can power any CIRCUITRON LED- type Strobe Flasher or EOT flasher from track power. Can be used as a constant lighting unit in unpowered rolling stock. 35 mA output will power 2-3 Strobes or EOT Flashers, LEDs with a 47 ohm resistor, one #7418 ot two be present whether train is moving forward or backward. Can be used with DC, AC or Carrier Control systems. .3x .3x .8".
...more about the Circuitron TP-1 Track Power Adapter

Features: Will power the ML-1 Mars Light and Strobe Flashers and also has outputs that will provide directional constant lighting. Fits most HO locos, can be used with motors drawing up to 1 amp.
...more about the Circuitron TP-2 Track Power Adapter

Features: Ideal for constant lighting source in unpowered rolling stock. No ballast lamps or motors required. Will power Mars flasher in models driven by low current can motors. Works with all forms of track power. Max current output is 1/2 amp.
...more about the Circuitron TP-3 Track Power Adapter

Features: * A low-cost circuit that alternately flashes two LEDs at a constant rate. * Animate emergency vehicles, signs, barricades, towers, etc. Simple to install. Powered by a 9V battery, or by using PS-3.
...more about the Circuitron Emergency Flasher -- .120'' Red

Features: Flashes LEDs or lamps. Connects to Detection Units. Maintains constant flash rate. 1.5 x 3" printed circuit board. Requires 10-18V AC or DC input. 250 ma. output.
...more about the Circuitron FL-2 Alternating Flasher

Features: * Specifically deigned for use at grade crossings, using Opto-Sensors to detect the train. Output controls flasher, gates, bells, etc. * Detects train when an Opto-Sensor is covered. Senses track polarity and activates only the Opto-Sensors for the direction of travel. Always turns off after the last piece of rolling stock clears the crossing. Includes four Opto-Sensors. Requires an Alternating Flasher Unit to operate flashing lamps. Note: DT-1 cannot detect a short train or loco if it falls between Opto-Sensors. Use in any scale with DC track power. 2 x 3" printed circuit board. 10-18V AC or DC input.
...more about the Circuitron DT-1 Grade Crossing Detection Unit