|
|
|
Features: * The Train Engineer walk-around wireless control system is ideally suited for backyard garden railroads and can be used for DC indoor/outdoor railroads of any size or gauge. * No modification to the locomotive is required. It use a 27 MGHZ multidirectional FM signal with Pulse Code Modification (P.C.M.) that eliminates any outside signal interference. It operates off of your normal power pack: just connect the receiver unit into existing wiring between the track layout and your power supply. * The Train Engineer gives you wireless control of your train within a 300-foot circle of the receiver unit and maintains all the functions of your power pack while enhancin
...more about the Crest Train Engineer Walk Around 2 Piece Set -- Includes #55471 Receiver & #55473 Transmitter/10 amp rating (2)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Features: * Now you can see what your railroad looks like from the engineer's point of view! With a camera slightly larger than the diameter of a quarter and only 3/4" deep, you can ride along with just about any loco. The camera broadcasts to the included receiver which is connected to a TV or VCR and you can watch all the action as if you were in the cab yourself. * System includes camera, microphone enclosed within camera case, receiver, 9V battery connector, a 36" two-wire A/V cable for easy positioning of receiver, 9V DC transformer for receiver and an 8V DC transformer for the camera.
...more about the Crest Video -- Train Remote View Camera System
|
Features: * Thus edition of the Train Engineer system eliminates the worry of clean track. Signal is transmitted via airwaves instead of through the track so it can run on battery or track power. Sound, all lighting functions and more can be operated from the handheld transmitter. Control up to 999 trains and accessories with one transmitter and identify every locomotive by both description and roadnumber. Innovative throttle allows easy and accurate operation. A graphic display walks you through all functions and a detailed manual is also included. * Includes receiver and handheld transmitter.
...more about the Crest Revolution Train Engineer 2.4 GHz -- For Large Scale Trains
|
|
|
Features: Scale size housing, easily mounted on any freight car. High-intensity LED slowly flashes a bright light rearward. Requires 3V input, easily obtained from two small batteries; the TP-1 Track Power (#800-2001), can be used if the car is equipped with track power pickups.
...more about the Circuitron End-Of-Train Flasher -- Red Light
|
Features: Alternately flashes two 1.7mm diameter, high-intensity, lens-end lamps (included) at a slow rate to simulate ditch lamps. With the addition of a DPST or DPDT switch, the DL-1 circuit can be bypassed so the lights stay on. Requires 2.4-3V DC input from batteries, TP-2 #800-2002 or TP-3.
...more about the Circuitron DL-1 Oscillating Ditch Lights
|
|
Features: Miniature voltage regulator can power any CIRCUITRON LED- type Strobe Flasher or EOT flasher from track power. Can be used as a constant lighting unit in unpowered rolling stock. 35 mA output will power 2-3 Strobes or EOT Flashers, LEDs with a 47 ohm resistor, one #7418 ot two be present whether train is moving forward or backward. Can be used with DC, AC or Carrier Control systems. .3x .3x .8".
...more about the Circuitron TP-1 Track Power Adapter
|
|
Features: Ideal for constant lighting source in unpowered rolling stock. No ballast lamps or motors required. Will power Mars flasher in models driven by low current can motors. Works with all forms of track power. Max current output is 1/2 amp.
...more about the Circuitron TP-3 Track Power Adapter
|
|
|
|
Features: * Specifically deigned for use at grade crossings, using Opto-Sensors to detect the train. Output controls flasher, gates, bells, etc. * Detects train when an Opto-Sensor is covered. Senses track polarity and activates only the Opto-Sensors for the direction of travel. Always turns off after the last piece of rolling stock clears the crossing. Includes four Opto-Sensors. Requires an Alternating Flasher Unit to operate flashing lamps. Note: DT-1 cannot detect a short train or loco if it falls between Opto-Sensors. Use in any scale with DC track power. 2 x 3" printed circuit board. 10-18V AC or DC input.
...more about the Circuitron DT-1 Grade Crossing Detection Unit
|
Features: * Specifically deigned for use at grade crossings, using Opto-Sensors to detect the train. Output controls flasher, gates, bells, etc. * Full logic system duplicates prototype grade crossing action. Does nt require sensor stay covered to activate. Integrated memory keeps output "on" until last car clears the crossing. Activates whenever a train approaches from either direction, If trains stop short then backs away, until will detect that and turn output "off." Independent of train length; will detect a short train even if it falls between Opto-Sensors. Includes four Opto-Sensors. 3 x 4" printed circuit board. 10-18V AC or DC input.
...more about the Circuitron Dt-2 Grade Crossing Detection Unit
|
Features: * Specifically deigned for use at grade crossings, using Opto-Sensors to detect the train. Output controls flasher, gates, bells, etc. * Single-direction unit for crossing where bi-directional detection is unnecessary, such as a mainline with trains traveling in only on direction. Operates with any train length. Completely independent of track power. Use in any scale. Requires 10-18V AC or DC input.
...more about the Circuitron DT-3 Single-Direction Grade Crossing Detection Unit
|
Features: Ideal for spotting a hidden train or piece of rolling stock. Four independent detection units combined onto one circuit board, can be used separately or together to control external devices. Supplied with four Opto-Sensors that mount between rails to detect movement. When train covers a sensor, the unit activates any connected DC accessory, such as an indicator light on a control panel. Independent sensitivity controls are provided for adjusting each Opto-Sensor to lighting conditions. Constructed on a 3 x 3" printed circuit board. Requires 10-18V DC. Independent of track power. Compatible with radio or carrier control systems.
...more about the Circuitron DT-4 Rolling Stock Detection Unit
|
Features: * Specifically deigned for use at grade crossings, using Opto-Sensors to detect the train. Output controls flasher, gates, bells, etc. * Single-direction grade crossing detector with alternating flasher ion one circuit board. Operates with any length train. Independent of track power. Use in any scales. Can power two 250 ma loads (five grain-of-wheat lamps or ten LEDs per side). 10-18V AC or DC input.
...more about the Circuitron DF-1 Grade Crossing Detector w/Flasher
|
|
|
Features: Solid state, provides positive power to dual-coil switch machines. Protects from burnout due to stuck pushbuttons, short circuits, etc. Operates off accessory terminals of power pack or transformer up to 25V. 24V input can activate 5 to 10 coils simultaneously if connected to same control. Instant recycle time. Includes a section of Printed Circuit Mounting Track (PCMT).
...more about the Circuitron Snapper Switch Machine Power Supply
|
