|
|
Features: A self-contained AC to DC converter with an adjustable voltage can be adjusted anywhere between 1.25 and 12.00 volts DC. Maximum continuous current output of the PS-2A is in excess of one amp. Ideal for powering any low current DC accessories including 1.5V micro-lamps. The AC or unfiltered DC input should be about 5-6V higher than the desired regulated aouput. The input voltage to allow maximum current output. The input voltage may be as high as 22V, but this may result in reduced current available at the output, particularly at lower voltage settings.
...more about the Circuitron PS-2A Converter & Regulator
|
Features: Changes direction when the Opto-Sensor is covered. Use for test track, window display, mine train or automatic reverse loop operation. Pushbuttons can be connected for manual reversing. Requires 12V DC power source. Constructed on 2 x 3" printed circuit board.
...more about the Circuitron AR-1 Automatic Reversing Circuit
|
Features: Same as AR-1, but with adjustable delay to hold train at sensor before reversing. Adjustable delay from one second to over one minute. Can be connected to pushbutton or DT-4 to permit stops and delays without reversing. Requires 12-18V DC power supply. Constructed on 3 x 3" printed circuit board.
...more about the Circuitron AR-2 Automatic Reverse w/Adjustable Delay
|
Features: * Tiny Opto-Sensors detect train movement. Sensors mount between the rails and activate circuitry when shaded from a passing train. Independent of track power, rolling stock requires no modifications. Sensors fit between ties and may be ballasted over in most cases. Circuitry is extremely sensitive and will operate properly under very low levels of room light. * Positive indication whenever a section of a layout is occupied by rolling stock. Contains all circuitry to power two-color block signals at each end of the protected block. Will give proper indications if a train leaves a block by backing out. No modifications to rolling stock needed. Completely bi-direct
...more about the Circuitron BD-1 Optical Detector
|
|
Features: Use with detection units for adjustable delay with self-contained relay on the output. Great for automatic stop at a station or siding. Time delay adjustable from 0 to over one minute. Requires 12V DC power supply.
...more about the Circuitron TD-1 Time Delay Circuit
|
Features: Activates dual-coil switch machine when used with DT-4. Momentary pulse when detection unit is activated, protects from burnout. Can be used to control both directions. Requires 10-18V AC or DC input. The higher the voltage, the greater the output power. Recycle time on each side is 1-2 seconds.
...more about the Circuitron TC-1 Automatic Turnout Control
|
|
|
Features: Electronic multi-chime diesel horn with speaker and push button. With external switches, DH-1 can produce three different single frequency tones, three different dual chime tones and three chime tone. Requires a 10-18V AC or DC input.
...more about the Circuitron DH-1 Diesel Horn Sound System
|
Features: * Timing circuitry for standard traffic light. Outputs drive LED or lamp signals (not included). * If LEDs are used, they must be common anode design. All four times are adjustable. Requires 10-18V AC or DC input. Red, yellow and green outputs provided for each direction (six total) and each can drive a 250mA maximum load. Adaptable for all scales.
...more about the Circuitron TL-1 Traffic Light Controller
|
Features: * Prototype turnouts don't snap open and closed, they move slowly. This easy-to-mount switch machine features prototypical slow-motion action-three seconds to complete throw. * Easy-to-mount slow-motion switch machine features: * Prototypical slow-motion action - three seconds to complete throw * Precision-engineered gear drive mechanism * Simple mounting with linkage included - no additional brackets or linkage necessary * Convenient auxilliary contacts - two sets SPDT provided * Easy wiring - two-wire connection possible.
...more about the Circuitron The Tortoise(TM) Switch Machine
|
Features: Smail (Slow Motion Actuator with Integrated Logic) features same size & mounting as the TORTOISE (sold separately). Compatible with all DCC systems that provide accessory address control. Two-wire connection to DCC bus with no external power necessary. Easy programming. May also be controlled with panel switches or detection circuits. Adjustable throw speed. Power up position user definable or will default to last used. Other specifications same as TORTOISE (#800-6000).
...more about the Circuitron The Smail(TM) Switch Machine w/Internal DCC Decoder -- Single
|
Features: * Mounting bracket and mechanism utilize the Tortoise(tm) (not included) and a special drive wire cable assembly to remotely actuate any crossing gate, train order or semaphore signal having a vertical control wire extending below the layout. Positive, adjustable stops are provided at both ends of travel. Can drive two cables from the one drive mechanism, if desired. * Adjustable for all scales.
...more about the Circuitron Tortoise -- Gate/Semaphore Actuator
|
|
|
|
|
|
|
Features: Plastic assembly provides simple snap-in mounting of all Circuitron printed circuit boards. Prepunched with mounting holes; can be mounted using screws, adhesive or double-backed tape. After PCMT is mounted, circuit boards simply snap into the track and can be easily be removed for service.
...more about the Circuitron Printed Circuit Mounting Track
|
Features: * Designed to drive the Tortoise Switch Machine (sold separately), this accessory decoder plugs directly on to the Tortoise simply connect to track power using the two handy screw terminals and the unit is ready to use. The Hare is compatible with all DCC systems that support accessory operations. And, many advanced features are provided to enhance operation including:. * Auto Throw automatically throws points when train approaches against the points. Eliminates derailments, layout shorts, loco and scenery damage, and is ideal for difficult to reach turnouts and hidden staging. Works with both insul-frog and electro frog turnouts for Versions I and II. * Smart Ro
...more about the DCC Specialties The ''Hare'' - Plug & Play Stationary DCC Decoder for Tortoise Switch Machines -- No Feedback
|
Features: * Designed to drive the Tortoise Switch Machine (sold separately), this accessory decoder plugs directly on to the Tortoise simply connect to track power using the two handy screw terminals and the unit is ready to use. The Hare is compatible with all DCC systems that support accessory operations. And, many advanced features are provided to enhance operation including. * Auto Throw automatically throws points when train approaches against the points. Eliminates derailments, layout shorts, loco and scenery damage, and is ideal for difficult to reach turnouts and hidden staging. Works with both insul-frog and electro frog turnouts for Versions I and II. * Smart Rou
...more about the DCC Specialties The Hare Plug & Play Stationary DCC Decoder for Tortoise Switch Machines -- With Feedback
|
Features: This advanced and affordable power supply was developed especially for DCC and can be used with Digitrax, Lenz, NCE and other systems. Features include grounded 16-gauge fail-safe, three wire input and output, illuminated rocker power switch, circuit breaker protection on output, and a sealed, impact-resistant enclosure. Input: 120V AC 60HZ; Output 15V AC 6 AMP.
...more about the DCC Specialties Magna Force DCC Power Supply
|
Features: Protect your system and accessories with these easy-to-use components. Each is rated at four amps and works without relays or a power supply. Simple screw terminals make them easy to add to existing wiring. Both are compatible with most DCC systems, however the Digitrax Zephyr and Atlas Commander do not have enough power to operate these units. Units are not for use with direct current (DC) applications.
...more about the DCC Specialties OnGuard DCC Accessories -- Auto Reverser-Breaker
|
Features: * Overcome programming problems with BLI, Soundtraxx and multiple decoder/loco combinations. Microprocessor controlled unit safely boosts and controls programming power to about 200 mA. When hooked up for programming, unit initially powers programming track to charge-up decoder components like capacitors that would otherwise reduce programming energy and cause a programming failure. Built-in circuit protection, with LED indicator, shuts down instantly in the event of an overload or short to protect the decoder and system programming circuits. * Compatible with Broadway Limited locos, Digitrax, Lenz, MRC, NCE, TCS and Soundtraxx decoders in both single and dual de
...more about the DCC Specialties PowerPax DCC Programming Booster
|
|
|
|
|
|
|
|
|
|
