Model Trains

Features: This power supply is fully filtered and regulated to within 3% over the fll range with no load to full load. Its protected against accidental shorting of the outputs and includes a EMI/RFI shield on the output cable. Its ideal for prjects where highly regulated voltage is important. Includes a 6' 12V output cord.
...more about the Ngineering Switching Power Supply -- 12VDC 1.25 Amp Regulated

Features: A unique blend of 62% tin, 36% lead and 2% silver alloy with a rosin flux core. The .020 diameter is well-suited for reaching tight spaces. Low melting point of 354-372F 179-189C makes it ideal for temperature-sensitive components. Includes dispenser tube.
...more about the Ngineering Low-Temperature Silver-Bearing Solder

Features: * This is the Monoject(R) #412, with a long, curved tip that allows easy access in tight places. The small tip opening of just .028 diameter provides precise dispensing control. It can be used with a wide variety of materials including glues, caulking, oils, grease, cleaners, soldering flux and more. * Holds up to .4 ounces 12cc of material to handle big jobs or for more work time between refills.
...more about the Ngineering Easy-Reach Curved Tip Syringe -- .028'' Diameter Tip Orifice, 12cc (.4 oz) Capacity

Features: Contains 51 strands of #46 wire, will carry 600 ma.
...more about the Ngineering Super-Flexible Insulated Electrical Wire - 5' -- #29

Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Provides flashes in short bursts similar to lights used on emergency vehicles. Multiple LEDs can be wired in series.
...more about the Ngineering Super Flashers -- Emergency Flasher

Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Flashes like a typical stop/caution signal.
...more about the Ngineering Super Flashers -- Signal Flasher

Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Alternately flashes a pair of LEDs (or up to 4 pair depending on power source). Each light is on for 3/4 second, typical of grade crossings, school zones etc.
...more about the Ngineering Super Flashers -- Alternating Flasher

Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Adjustable flash rate from 30 times per second to once every three seconds. On time and off time are equal (50% duty cycle).
...more about the Ngineering Super FLashers -- Variable Rate Flasher

Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Alternately flashes a pair of LEDs (or up to 4 pair depending on power source). Adjustable flash rate from 30 times per second to once every three seconds. On time and off time are equal (50% duty cycle).
...more about the Ngineering Super Flashers -- Variable Rate Alternating Flasher

Features: Design allows any color LED to be tested. No need to worry about choosing the proper resistor for protect the LED. simply snap the tester n a 9V battery and start testing. Includes spring-loaded contact block to hold wired LEDs.
...more about the Ngineering LED Tester

Features: * Smaller than any decoder at just .31" x .31" x .118" and utilizing the industry's smallest microcontroller and associated voltage control circuitry, the total module consumes less than 500 a (<1/2 ma). Typical peak operating current for these modules with LED(s) attached and running through full brightness curves range from 18-38 ma. This makes them ideally suited for operation when powered directly by a function output of any of today's HO, N or Z-scale DCC decoders. Designed specifically to provide truly realistic lighting effects for 20ma LEDs, these modules include input protection against reverse polarity. Input voltage range 6-18 VDC. On-board current li
...more about the Ngineering Ultra-Miniature Lighting Effects -- Mars Light Simulator

Features: * Smaller than any decoder at just .31" x .31" x .118" and utilizing the industry's smallest microcontroller and associated voltage control circuitry, the total module consumes less than 500 a (. * Provides a single repeating burst, increasing and decreasing in intensity to accurately represent roof beacons like those made by Prime and Federal used by most railroads.
...more about the Ngineering Ultra-Miniature Lighting Effects -- Beacon Simulator

Features: * Smaller than any decoder at just .31" x .31" x .118" and utilizing the industry's smallest microcontroller and associated voltage control circuitry, the total module consumes less than 500 a (. * Generates a varying (bell curve like) intensity to accurately represent Gyralight motion.
...more about the Ngineering Ultra-Miniature Lighting Effects -- Gyralight Simulator

Features: * Smaller than any decoder at just .31" x .31" x .118" and utilizing the industry's smallest microcontroller and associated voltage control circuitry, the total module consumes less than 500 a (. * Provides output for two LEDs, both on, then switches to alternating with realistic ramping of intensity when input is grounded (or activated by DCC function control).
...more about the Ngineering Ultra-Miniature Lighting Effects -- Ditch Light Simulator

Features: * Servo-Master activation system works with crossing gates and semaphores. * Each system is capable of operating two crossing gates with flashing lights or two semaphores.
...more about the NJ International Servo Master Activation System -- For Crossing Gates & Semaphores In All Scales w/Realistic Operation

Features: Expansion kits will allow up to 3 additional bi-directional tracks.
...more about the NJ International Servo Master Activation System Accessories -- Expander Kit

Features: Flasher Module alternately lights crossing signal lamps at a rate of 80 times per minute. Designed for 12-16V operation.
...more about the NJ International Flasher Module

Features: Keep Throttles Off Layout Scenery with Throttle Pockets™ During layout operating sessions modelers are always looking for a place to set down their throttles. Universal Throttle Pockets from New Rail Models offer a convenient alternative to leaving throttles on the scenery or trackwork. These durable injection-molded plastic throttle holders attach to layout fascia panels. Can be used with DCC handheld throttles from all major manufacturers including the latest MRC Prodigy handhelds.
...more about the New Rail Models Universal Throttle Pocket (ABS) -- Single - Holds Atlas, CVP, Digitrax, Lenz, NCE & MRC Throttles

Features: * Simplify installation of Blue Point(TM) Turnout Controllers (sold separately) with this complete and easy to use system. A wood knob mounted on the fascia is connected to a nylon push-pull tube, which then connects to the Controller. Tubes are 3' (91.4cm) long, and can be bent into tight curves, or cut to fit as needed. * Everything you need to install one Blue Point Controller (sold separately) including one pre-drilled wood knob, one 2-56 screw to attach the knob to the inner tube, one 3' flexible tube (contains both an inner and outer tube), two tube clamps with screws that anchor the outer tube at each end, one cable bracket to hold the outer tube at the Bl
...more about the New Rail Models Flex Link(TM) -- Starter Kit