Scale size housing, easily mounted on any freight car. High-intensity LED slowly flashes a bright light rearward. Requires 3V input, easily obtained from two small batteries; the TP-1 Track Power (#800-2001), can be used if the car is equipped with track power
...more about the Circuitron End-Of-Train Flasher -- Red Light
|
Alternately flashes two 1.7mm diameter, high-intensity, lens-end lamps (included) at a slow rate to simulate ditch lamps. With the addition of a DPST or DPDT switch, the DL-1 circuit can be bypassed so the lights stay on. Requires 2.4-3V DC input f rom batteries, TP-2 #800-2002 or
...more about the Circuitron DL-1 Oscillating Ditch Lights
|
|
|
Miniature voltage regulator can power any CIRCUITRON LED- type Strobe Flasher or EOT flasher from track power. Can be used as a constant lighting unit in unpowered rolling stock. 35 mA output will power 2-3 Strobes or EOT Flashers, LEDs with a 47 o hm resistor, one #7418 ot two be present whether train is moving forward or backward. Can be used with DC, AC or Carrier Control
...more about the Circuitron TP-1 Track Power Adapter
|
|
|
Ideal for constant lighting source in unpowered rolling stock. No ballast lamps or motors required. Will power Mars flasher in models driven by low current can motors. Works with all forms of track power. Max current output is 1/2
...more about the Circuitron TP-3 Track Power Adapter
|
|
|
|
Specifically deigned for use at grade crossings, using Opto-Sensors to detect the train. Output controls flasher, gates, bells, etc. Detects train when an Opto-Sensor is covered. Senses track polarity and activates only the Opto-Sensors for the dir ection of travel. Always turns off after the last piece of rolling stock clears the crossing. Includes four Opto-Sensors. Requires an Alternating Flasher Unit to operate flashing lamps. Note; DT-1 cannot detect a short train or
...more about the Circuitron DT-1 Grade Crossing Detection Unit
|
Specifically deigned for use at grade crossings, using Opto-Sensors to detect the train. Output controls flasher, gates, bells, etc. Full logic system duplicates prototype grade crossing action. Does nt require sensor stay covered to activate. Inte grated memory keeps output ''on'' until last car clears the crossing. Activates whenever a train approaches from either direction, If trains stop short then backs away, until will detect that and turn output ''off.'' Independent
...more about the Circuitron Dt-2 Grade Crossing Detection Unit
|
Specifically deigned for use at grade crossings, using Opto-Sensors to detect the train. Output controls flasher, gates, bells, etc. Single-direction unit for crossing where bi-directional detection is unnecessary, such as a mainline with trains tr aveling in only on direction. Operates with any train length. Completely independent of track power. Use in any scale. Requires 10-18V AC or DC
...more about the Circuitron DT-3 Single-Direction Grade Crossing Detection Unit
|
Ideal for spotting a hidden train or piece of rolling stock. Four independent detection units combined onto one circuit board, can be used separately or together to control external devices. Supplied with four Opto-Sensors that mount between rails to detect movement. When train covers a sensor, the unit activates any connected DC accessory, such as an indicator light on a control panel. Independent sensitivity controls are provided for adjusting each Opto-Sensor to lighting
...more about the Circuitron DT-4 Rolling Stock Detection Unit
|
Specifically deigned for use at grade crossings, using Opto-Sensors to detect the train. Output controls flasher, gates, bells, etc. Single-direction grade crossing detector with alternating flasher ion one circuit board. Operates with any length t rain. Independent of track power. Use in any scales. Can power two 250 ma loads (five grain-of-wheat lamps or ten LEDs per side). 10-18V AC or DC
...more about the Circuitron DF-1 Grade Crossing Detector w/Flasher
|
|
Solid state, provides positive power to dual-coil switch machines. Protects from burnout due to stuck pushbuttons, short circuits, etc. Operates off accessory terminals of power pack or transformer up to 25V. 24V input can activate 5 to 10 coils si multaneously if connected to same control. Instant recycle time. Includes a section of Printed Circuit Mounting Track
...more about the Circuitron Snapper Switch Machine Power Supply
|
|
A self-contained AC to DC converter with an adjustable voltage can be adjusted anywhere between 1.25 and 12.00 volts DC. Maximum continuous current output of the PS-2A is in excess of one amp. Ideal for powering any low current DC accessories inclu ding 1.5V micro-lamps. The AC or unfiltered DC input should be about 5-6V higher than the desired regulated aouput. The input voltage to allow maximum current output. The input voltage may be as high as 22V, but this may result in
...more about the Circuitron PS-2A Converter & Regulator
|
Changes direction when the Opto-Sensor is covered. Use for test track, window display, mine train or automatic reverse loop operation. Pushbuttons can be connected for manual reversing. Requires 12V DC power source. Constructed on 2 x 3'' printed c ircuit
...more about the Circuitron AR-1 Automatic Reversing Circuit
|
