Cir-Kit Model Trains

Tapewire is an adhesive-backed Mylar tape containing electrical conductors. The tape is.005 thick by 5/8'' wide and can be painted. It can be run under grass mats or behind wallpaper. Tapewire can be used throughout the layout, but is most useful w here ''invisible'' wiring is desired. Connections are pinned together with brads and do not require
...more about the Cir-Kit Concepts Inc Tapewire -- 2 Conductor (15')

For connecting tapewire system to transformer lead-in. Use with
...more about the Cir-Kit Concepts Inc Junction Splice

For connecting transformer to tapewire system. Plug on one end mates with Junction Splice. Opposite ends of 6' lead connect to transformer
...more about the Cir-Kit Concepts Inc Transformer Lead-In Wire

Miniature swivel spotlight features top mounted 360 side-to-side movement. Large size bulb is a highly focused lens for light concentration and will burn for 5000+ hours. Bulb snaps in and works on a 12V system. 7/8'' long, 3/8''
...more about the Cir-Kit Concepts Inc Swivel Spotlight

5/64'' 2.0mm diameter. Use wherever a ''to scale'' flame look is desired. Solid 1'' wire terminals. 12V
...more about the Cir-Kit Concepts Inc Bulb -- 12V Micro-Flame w/Wire Terminals

SPDT, for turning lights and accessories on and off. Only 1/4 x 7/16'' in size. For tape or conventional wiring systems. Instructions included. Pound-in
...more about the Cir-Kit Concepts Inc Switch -- Miniature Slide

For making small holes for brass brads. Eliminates the risk of making holes that are too
...more about the Cir-Kit Concepts Inc Pilot Hole Punch

Used for connecting tapewire and conventional wiring systems. No soldering required. Used for connecting tapewire and conventional wiring systems. No soldering is
...more about the Cir-Kit Concepts Inc Brass Brads 1/8''

Fuse holder and wire sockets for in-line conmnection. Fuse not
...more about the Cir-Kit Concepts Inc In-Line Fuse Holder

Used for connecting tapewire and conventional wiring systems. No soldering
...more about the Cir-Kit Concepts Inc Headless Pins (36)

One end is crimped onto conventional wire. The other end may be plugged into headless pins and pinned to tapewire
...more about the Cir-Kit Concepts Inc Wire Sockets (22)

Excellent for holding and inserting 1/8'' brass brads. Serrated teeth on both
...more about the Cir-Kit Concepts Inc Short Nose Pliers

Includes transformer lead-in wire, junction splice, pilot hole punch and needles, 15' tarewire, test probe and 1/8'' brass
...more about the Cir-Kit Concepts Inc Basic Wiring Kit II

Five nickel-plated screwdrivers. Blade range of.049
...more about the Cir-Kit Concepts Inc Jeweler's Screwdriver Set -- Blade range of .049 to .079

Works with any 10 watt or larger 12V transformer, even a car battery. Melts solder in 3-4
...more about the Cir-Kit Concepts Inc Low Voltage Soldering Iron

The perfect tool for any modeler using tapewire! Made of stainless steel with a plastic coated handle, the brad placement tool holds brads firmly in place during
...more about the Cir-Kit Concepts Inc Brad Placement Tool

Used to directly connect 1.5V micro bulbs to a 12V source. A resistor must be connected to each
...more about the Cir-Kit Concepts Inc Dropping Resistor (3)

Use for 18 to 24 gauge wire. May be crimped or
...more about the Cir-Kit Concepts Inc Spade Lugs

For connections where flat tape is not practical. Very fine, stranded, #32
...more about the Cir-Kit Concepts Inc Miniature Wire -- 2 Conductor Hook-Up

For connections where flat tape is not
...more about the Cir-Kit Concepts Inc Miniature Wire -- 1 Conductor

ith this all-electric variable controller, any lamp up to 300 watts may be dimmed or the small power tool up to 2.5
...more about the Cir-Kit Concepts Inc Dimmer Extension Cord

Works with any 12V system and requires no separate transformer. The orange-colored bulb is a replaceable screw base type with a MH658 plug attached to the small gauge along with a 24'' long power
...more about the Cir-Kit Concepts Inc Glowing Embers