Super Glue
Shop online for 162 super glue at discounts up to 38%. Building Supplies is the most popular of the 3 super glue categories, then Arts & Crafts, and Plastic Models. Hobbylinc is ranked #1 out of 19 super glue manufacturers, followed by Pacer Glues, and Bob Smith Industries.
Sub-Categories for Super Glue
Products of Super Glue
1-20 of 162 | Sort by: |
Hobbylinc # hlc107
Add To Cart | Wish List |
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .
SALE
23% Off
Hobbylinc # hlc108
Add To Cart | Wish List |
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .
SALE
26% Off
Zap-A-Gap CA+ 1 oz.
$9.19 $7.59
Pacer # paapt02
Add To Cart | Wish List |
Excellent Gap-Filling Super-Glue Zap-A-Gap 1 oz bottle from Pacer Glues.
SALE
27% Off
Hobbylinc # hlc102
Add To Cart | Wish List |
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.
SALE
23% Off
Hobbylinc # hlc113
Add To Cart | Wish List |
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars.
Website security verified by GoDaddy
Hobbylinc # hlc151
Add To Cart | Wish List |
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.
SALE
23% Off
Hobbylinc # hlc103
Add To Cart | Wish List |
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. .
SALE
26% Off
Pacer # paapt29
Add To Cart | Wish List |
Pacer ZIP KICKER Super-Glue accelerator is the best working accelerator for ZAP and other super glues you'll ever find! A little spritz works in seconds.
Hobbylinc # hlc112
Add To Cart | Wish List |
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars.
Hobbylinc # hlc161
Add To Cart | Wish List |
UN-CURE debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water.
SALE
23% Off
Hobbylinc # hlc106
Add To Cart | Wish List |
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
SALE
22% Off
Hobbylinc # hlc152
Add To Cart | Wish List |
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.
SALE
23% Off
Hobbylinc # hlc111
Add To Cart | Wish List |
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. . Learn about how to Select a Super Glue.
Insta-Cure Gap Filling 2oz
$11.99 $9.59
Insta-Set 3.75 fl oz Aerosol Accelerator F.S.
Hobby CA Super Glue
$13.99 $10.89
* currently unavailable
SALE
22% Off
SALE
23% Off
Hobbylinc # hlc109
Add To Cart | Wish List |
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .
SALE
23% Off
Hobbylinc # hlc101
Add To Cart | Wish List |
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. .