Glues
Shop online for over 300 glues at discounts up to 56%. Plastic Cement is the most popular of the 10 glues categories, then CA Super Glue, and CA Super Glue Accelerator. Hobbylinc is ranked #1 out of 48 glues manufacturers, followed by Tamiya, and Testors.
Sub-Categories for Glues
Products of Glues
Hobbylinc # hlc151
Add To Cart | Wish List |
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.
Hobbylinc # hlc107
Add To Cart | Wish List |
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .
Tamiya # tam87038
Add To Cart | Wish List |
Extra-thin plastic model cement with applicator brush. Used to glue parts already held together. The thin glue will wick into the joint for a firm bond.
Scenic Cement 16 oz
$9.99 $7.99
Woodland # woos191
Add To Cart | Wish List |
Ready to use matte-medium that is a multi use product for Ballast, Turf, etc.
Testors # tes3501
Add To Cart | Wish List |
This is a 5/8oz Tube of Cement for Plastic Models from Testors. For Ages 8 and Up.
Testors # tes3503
Add To Cart | Wish List |
This is a 5/8oz Tube of Fast Wood Cement for Wood Models from Testors.
Website security verified by GoDaddy
SALE
23% Off
Hobbylinc # hlc108
Add To Cart | Wish List |
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .
Quik-Cure 5min Epoxy 9oz
$22.99 $18.29
SALE
26% Off
SALE
37% Off
Testors # tes290278
Add To Cart | Wish List |
This is a Value Pack 7/8oz Tube of Cement for Plastic Models from Testors. For Ages 8 and Up.
Zap-A-Gap CA+ 1 oz.
$9.19 $7.59
Pacer # paapt02
Add To Cart | Wish List |
Excellent Gap-Filling Super-Glue Zap-A-Gap 1 oz bottle from Pacer Glues.
Revell-Germany # rvl39604
Add To Cart | Wish List |
This is the Revell-Germany 25g Professional Liquid Cement w/Applicator plastic model cement.
SALE
27% Off
Hobbylinc # hlc102
Add To Cart | Wish List |
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.