|
|
|
|
|
Features: Much smaller than the typical 3mm LED, this SMD device has a ceramic case with gold-plated solder pads on the back. Produces a very bright, pure white light output. Requires appropriate current limiting resistor, sold separately. Device Voltage: 3.6V DC, Current: 20 Ma, Average Life: 50-80,000 hours.
...more about the Ngineering Super White LEDs 2 x 3mm -- 2-Pack
|
|
|
|
|
|
|
|
|
|
Features: This power supply is fully filtered and regulated to within 3% over the fll range with no load to full load. Its protected against accidental shorting of the outputs and includes a EMI/RFI shield on the output cable. Its ideal for prjects where highly regulated voltage is important. Includes a 6' 12V output cord.
...more about the Ngineering Switching Power Supply -- 12VDC 1.25 Amp Regulated
|
Features: A unique blend of 62% tin, 36% lead and 2% silver alloy with a rosin flux core. The .020 diameter is well-suited for reaching tight spaces. Low melting point of 354-372F 179-189C makes it ideal for temperature-sensitive components. Includes dispenser tube.
...more about the Ngineering Low-Temperature Silver-Bearing Solder
|
|
|
|
Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Provides flashes in short bursts similar to lights used on emergency vehicles. Multiple LEDs can be wired in series.
...more about the Ngineering Super Flashers -- Emergency Flasher
|
Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Flashes like a typical stop/caution signal.
...more about the Ngineering Super Flashers -- Signal Flasher
|
Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Alternately flashes a pair of LEDs (or up to 4 pair depending on power source). Each light is on for 3/4 second, typical of grade crossings, school zones etc.
...more about the Ngineering Super Flashers -- Alternating Flasher
|
Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Adjustable flash rate from 30 times per second to once every three seconds. On time and off time are equal (50% duty cycle).
...more about the Ngineering Super FLashers -- Variable Rate Flasher
|
Features: * Flashers automatically support all colors of 20ma LEDs with no additional resistors required. Colors can be mixed on the same circuit. Will drive multiple LEDs in series depending on power supply voltage. Resistors can be added to on-board solder pads for LED brghtness control. Input: 7-16V DC Less than 1" square. LEDs sold separately. * Alternately flashes a pair of LEDs (or up to 4 pair depending on power source). Adjustable flash rate from 30 times per second to once every three seconds. On time and off time are equal (50% duty cycle).
...more about the Ngineering Super Flashers -- Variable Rate Alternating Flasher
|
LED Tester by Ngineering
|
| $8.95 $8.05 |
Product Number ngin8021 |
Availability Usually ships out in 3-4 Days |
Features: Design allows any color LED to be tested. No need to worry about choosing the proper resistor for protect the LED. simply snap the tester n a 9V battery and start testing. Includes spring-loaded contact block to hold wired LEDs.
...more about the Ngineering LED Tester
|
Features: * Smaller than any decoder at just .31" x .31" x .118" and utilizing the industry's smallest microcontroller and associated voltage control circuitry, the total module consumes less than 500 a (<1/2 ma). Typical peak operating current for these modules with LED(s) attached and running through full brightness curves range from 18-38 ma. This makes them ideally suited for operation when powered directly by a function output of any of today's HO, N or Z-scale DCC decoders. Designed specifically to provide truly realistic lighting effects for 20ma LEDs, these modules include input protection against reverse polarity. Input voltage range 6-18 VDC. On-board current li
...more about the Ngineering Ultra-Miniature Lighting Effects -- Mars Light Simulator
|
Features: * Smaller than any decoder at just .31" x .31" x .118" and utilizing the industry's smallest microcontroller and associated voltage control circuitry, the total module consumes less than 500 a (. * Provides a single repeating burst, increasing and decreasing in intensity to accurately represent roof beacons like those made by Prime and Federal used by most railroads.
...more about the Ngineering Ultra-Miniature Lighting Effects -- Beacon Simulator
|
|
|
Features: * Smaller than any decoder at just .31" x .31" x .118" and utilizing the industry's smallest microcontroller and associated voltage control circuitry, the total module consumes less than 500 a (. * Provides output for two LEDs, both on, then switches to alternating with realistic ramping of intensity when input is grounded (or activated by DCC function control).
...more about the Ngineering Ultra-Miniature Lighting Effects -- Ditch Light Simulator
|
|
|
|
|
|
|