Quick drying cement for plastic models. New $1.59 (23% off). Joins polystyrene, the plastic models are made from, to polystyrene and polystyrene to wood.

This is the 6oz (170g) NCF Quick Aerosol Instant Glue Accelerator from Hot Stuff. New $10.19 (21% off). Features: Speeds drying time of all instant glues Can be pre-applied to surface or applied to exposed glue Stays active up to three minutes.

INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. New $4.99 (16% off). Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. . Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used pr

Excellent Gap-Filling Super-Glue. New $6.19 (26% off). Features: * Allows 7 to 10 seconds for positioning. * Cures in 20 seconds. * Accelerate with KICKER (paapt15). * Bonds anything, even oily surfaces! * Works best on: Metal, Wood, Rubber, Pottery, Most Plastics, Aluminum, Ceramic.

INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. New $8.19 (18% off). Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. . Features: INSTA-CURE+ is a gap filling glue that dries in 5-15 sec.

Hot Stuff super-glues have a consistency resembling that of water and are used mainly for bonding parts which fit very well. New $7.79 (25% off). Sets in 10 seconds. Those who are sensitive to cyanoacrylate curing fumes will enjoy using new UFO (hotufo4) in place of regular HOT STUFF.

Wood model glue. New $1.89 (22% off). Features: * Strong bond specially formulated for wood. * Extra Fast drying.

INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. New $4.69 (21% off). INSTA-SET in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET significantly enhances a joint's strength. For difficult to bond materials, INSTA-SET can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occ

MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. New $7.79 (22% off). When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars. Learn about how to Found In : Building Supplies  >  Glues  >  CA Super Glue

INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. New $5.59 (44% off). Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. . Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered.

This is a Plastic Weld Cement. New $2.99 (20% off). Features: * Brush in cap. * Cements by capillary action. * Sets in minutes. * Used for bonding Plastruct ABS, Styrene, Butyrate or Acrylic to each other, or in combination.

Super 'T' has a consistency similar to that of syrup and has the ability to fill small gaps between parts which don't fit perfectly. New $7.79 (25% off). SUPER 'T' cures at a slower rate than HOT STUFF, (10-25 seconds depending on the material).

Ready to use matte-medium that is a multi use product for Ballast, Turf, etc. New $7.29 (18% off). Features: * Non-toxic, water based cement. * Spray with Scenic Sprayer (woos192) or brush on. * Dries to a clear, matte finish.

This is a Value Pack 7/8oz Tube of Cement for Plastic Models from Testors. New $2.69 (26% off). For Ages 8 and Up. Features: Quick drying cement for plastic models Joins polystyrene to polystyrene and polystyrene to wood Also useful for repairing household items made of polystyrene or ABS plastics Carded packaging.

For polystyrene (plastic models), ABS, acetate, plexiglass and many other plastics.. New $2.89 (21% off).

Super glue accelerator. New $9.29 (26% off). Best working accelerator for ZAP and all other super glues you'll find! Sets in just a few seconds.

IC-2000 is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. New $7.89 (21% off). The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered. INSTA-CURE is a highly refined CA which, combined with its freshness, gives a guaranteed 2 year shelf life. CAs are reactive monomers that chemically link (polymerize) when pressed into a thin film. The very thin lay

Ultra Solvent is a remarkable debonder and cleaner for any instant glue. New $6.59 (26% off). Use it for hand clean-up when ever you are manipulating small parts with your fingertips (instant glues make a thin, hard shell when cured on fingertips, reducing one's ability to work skillfully with tiny pieces) or just to get it off at the end of the day. Use Ultra Solvent to remove instant glue from most clothing and surfaces. Some fabric, colorings or materials may be affected, so test-patch on an inconspicuous place. Ultra Solvent is not a thinner for instant glue.

MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. New $4.88 (18% off). When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars. Cyanoacrylates (CAs) have become

Extra-thin plastic model cement with applicator brush. New $4.39 (20% off). Used to glue parts already held together. The thin glue will wick into the joint for a firm bond. Features: Excellent for plastic models (polystyrene plastic).