Building Supplies

Testors #TES3501. This is a 5/8oz Tube of Cement for Plastic Models from Testors. For Ages 8 and Up.

Hot-Stuff #HOTQA-6. This is the 6oz (170g) NCF Quick Aerosol Instant Glue Accelerator from Hot Stuff.

Testors #TES2547C. This is a 1/3 oz (10 mL) Enamel Gloss Black Paint Marker from Testors.

Hobbylinc #HLC107. INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .

Pacer #PAAPT02. Excellent Gap-Filling Super-Glue.

Hobbylinc #HLC108. INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .

Testors #TES9161. This is a Plastic Model Finishing Set for Cars and Trucks from Testors.

Hot-Stuff #HOTHS-4. This is a 2 oz. Bottle of Thin Hot Stuff Glue. It's for experienced modelers. Hot Stuff is the Adhesive that started the Super Glue Revolution! Not safe for foam. For foam applications use epoxy or foam-safe CA.

Badger #BAD50-0052. This is a 3/4 Oz. Glass Paint Jar with Cover from Badger.

Hobbylinc #HLCKIT-03. Supplies that picture-perfect model. The best of everything for building the highest quality models. Great gift for the experienced modeller.

Hobbylinc #HLC113. MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars.

Hobbylinc #HLC151. INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.

Testors #TES3503X. Wood model glue.

Testors #TES9131. This is a Testors Military Flat Enamel Paint Kit. Used for Decorating and Camouflaging Tanks, Ships, Planes & Figures of Nations.

Tamiya #TAM81040. This is a 250ml Bottle of Tamiya color Acrylic Paint (Thinner).

Hobbylinc #HLC103. INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. .

Microbrush #MCBMHS10. Precise applicator brush for glues, paints, and solvents.

Plastruct #PLS00002. This is a Plastic Weld Cement.

Tamiya #TAM81301. 23ml Jar of Tamiya XF-1 Black color Acrylic Flat (Matt) Paint.

Testors #TES1749. This is a 1/2 oz (14.7mL) glass jar of Enamel Flat Black Paint from Testors.