1-4 of 4 results in Building Supplies  >  Hobbylinc.

Hobbylinc Building Supplies On Sale

Online shopping for hobbylinc building supplies on sale, saving you up to 26%.

Hobbylinc Building Supplies On Sale Categories

4 Hobbylinc Building Supplies On Sale Products

Search Options
Hobbylinc INSTA-CURE Super Thin Cyanoacrylate 1oz Hobby CA Super Glue #102
Sale
40% Off

INSTA-CURE Super Thin Cyanoacrylate 1oz

Hobby CA Super Glue

$5.99
$3.59
 
In Stock
Earn
102
Rewards
Hobbylinc #HLC102. INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.
 
(20)
Location : CA Super Glue
Hobbylinc Inst-Cure+ Pocket Ca 1/4oz. Gap Filling CA W/Pin in cap Hobby CA Super Glue #133
Sale
30% Off

Inst-Cure+ Pocket Ca 1/4oz. Gap Filling CA W/Pin in cap

Hobby CA Super Glue

$4.99
$3.49
 
In Stock
Earn
99
Rewards
Hobbylinc #HLC133. INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
Location : CA Super Glue
Hobbylinc Insta-Cure Pocket CA 4 oz. Super thin CA W/Pin in cap Hobby CA Super Glue #132
Sale
27% Off

Insta-Cure Pocket CA 4 oz. Super thin CA W/Pin in cap

Hobby CA Super Glue

$16.98
$12.29
 
In Stock
Earn
350
Rewards
Hobbylinc #HLC132. INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.
Location : CA Super Glue
Hobbylinc FINISH CURE 20 Minute Epoxy (4 1/2oz) Hobby Epoxy #209
Sale
26% Off

FINISH CURE 20 Minute Epoxy (4 1/2oz)

Hobby Epoxy

$11.99
$8.78
 
In Stock
Earn
250
Rewards
Hobbylinc #HLC209. FINISH-CURE 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CURE can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing. For best results, FINISH-CURE should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on FINISH-CURE. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light we
Location : Epoxy
The #1 Source for Hobby Products!
Help
Account
Cart
x