A-Line, Du-bro or Hobbylinc Glues

Shop online for 55 a-line, du-bro or hobbylinc glues at discounts up to 31%. CA Super Glue is the most popular of the 6 a-line, du-bro or hobbylinc glues categories, then Accessories, and Epoxy.

Sub-Categories for A-Line, Du-bro or Hobbylinc Glues

Products of A-Line, Du-bro or Hobbylinc Glues

Extra Cyanoacrylate Tops

CA Glue Tip Glue Applicator
$0.75 $0.69
Hobbylinc # hlc312
  Add To Cart
Wish List
Replacement top that is on all of BSI's non-Pocket CAs.

INSTA-CURE Gap Filling Cyanoacrylate 1oz

Hobby CA Super Glue
$5.99 $5.09
Hobbylinc # hlc107
  Add To Cart
Wish List
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .

INSTA-CURE Gap Filling Cyanoacrylate 2oz

Hobby CA Super Glue
$9.99 $8.39
Hobbylinc # hlc108
  Add To Cart
Wish List
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .

INSTA-SET Cyanoacrylate Accelator 2oz

Hobby CA Super Glue Accelerator
$5.99 $5.09
Hobbylinc # hlc151
  Add To Cart
Wish List
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.

QUICK CURE 5 Minute Epoxy (9oz)

Hobby Epoxy
$18.99 $14.59
SALE
23% Off
Hobbylinc # hlc202
  Add To Cart
Wish List
QUIK-CURE 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE can be handled after 15 minutes. Full strength is reached in 1 hour.

MAXI-CURE Extra Thick Cyanoacrylate 2oz

Hobby CA Super Glue
$9.99 $8.29
* currently unavailable
Hobbylinc # hlc113
  Pre-Order
Wish List
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars.
Website security verified by GoDaddy

INSTA-CURE Super Thin Cyanoacrylate 2oz

Hobby CA Super Glue
$9.99 $8.39
Hobbylinc # hlc103
  Add To Cart
Wish List
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. .

INSTA-CURE Super Thin Cyanoacrylate 1oz

Hobby CA Super Glue
$5.99 $5.09
Hobbylinc # hlc102
  Add To Cart
Wish List
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.

Extra Fine Extender Tips (6)

Glue Tip Glue Applicator
$3.99 $3.29
Hobbylinc # hlc302
  Add To Cart
Wish List
For use over the standard #312 top, it allows BSI's thin CAs (Insta-Cure, Insta-Flex and Super-Gold) to be applied a drop at a time.

INSTA-CURE Gap Filling Cyanoacrylate 1/2oz

Hobby CA Super Glue
$3.99 $3.49
Hobbylinc # hlc106
  Add To Cart
Wish List
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

MAXI-CURE Extra Thick Cyanoacrylate 1oz

Hobby CA Super Glue
$5.99 $4.99
Hobbylinc # hlc112
  Add To Cart
Wish List
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best for bonding the tires for R/C cars.

INSTA-CURE Super Thin Cyanoacrylate 1/2oz

Hobby CA Super Glue
$3.99 $3.49
Hobbylinc # hlc101
  Add To Cart
Wish List
INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond. .

MAXI-CURE Extra Thick Cyanoacrylate 1/2oz

Hobby CA Super Glue
$3.99 $3.39
Hobbylinc # hlc111
  Add To Cart
Wish List
MAXI-CURE extra thick CA is the best CA for most plastics, including GE's Lexan MAXI-CURE is the best choice for plastic model assembly. When used with INSTA-SET, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. . Learn about how to Select a Super Glue.
SALE
31% Off
Hobbylinc # hlc120
  Add To Cart
Wish List
INSTA-FLEX clear rubber toughened has similar qualities to our black IC-2000 but can be used in applications where you do not want the adhesive to be seen. .

INSTA-CURE Gap Filling CA 8 oz REFILL

Hobby CA Super Glue
$29.99 $24.89
* currently unavailable
Hobbylinc # hlc109
  Pre-Order
Wish List
INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, dont spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out. .

MID CURE 15 Minute Epoxy (9oz)

Hobby Epoxy
$18.99 $14.59
SALE
23% Off
Hobbylinc # hlc204
  Add To Cart
Wish List
MID-CURE 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE in most applications. MID-CURE is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.

INSTA-SET Refill Cyanoacrylate 8oz

Hobby CA Super Glue Accelerator
$11.99 $9.19
* currently unavailable
SALE
23% Off
Hobbylinc # hlc152
  Pre-Order
Wish List
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.

QUICK CURE 5 Minute Epoxy (4 1/2oz)

Hobby Epoxy
$11.99 $9.79
Hobbylinc # hlc201
  Add To Cart
Wish List
QUIK-CURE 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE can be handled after 15 minutes. Full strength is reached in 1 hour.

UN-CURE Cyanoacrylate Debonder 1oz

Hobby CA Super Glue Debonder
$3.99 $3.49
Hobbylinc # hlc161
  Add To Cart
Wish List
UN-CURE debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water.

Insta-Set 3.75 fl oz Aerosol Accelerator F.S.

Hobby CA Super Glue
$11.99 $8.99
SALE
25% Off
Hobbylinc # hlc155
  Add To Cart
Wish List
INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization.