INSTA-CURE Gap Filling Cyanoacrylate 1oz

INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ should also be used. To prevent premature curing, don't spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.

Hobbylinc INSTA-CURE Gap Filling Cyanoacrylate 1oz Hobby CA Super Glue #107
 (118)
 Hobbylinc # hlc107
$5.49
 
Retail $6.99  SAVE 21% !
Hobbylinc Item # hlc107
Features :

INSTA-CURE+ is a gap filling glue that dries in 5-15 sec.

Out of Stock
Website security verified by GoDaddy.

Spotlight Review

 
"Excellent!"
nscrfns (Killeen, TX)
This is my go to CA glue. Use an extender tip to get very small amounts in a precise location. Get an extra tip and don't cut it open so you can put it on the bottle after gluing. Put the tip that has been cut and the extender tip in a jar of acetone to dissolve glue build up and keep tips like new.

You Might Also Like

← Swipe To View More →

Features

INSTA-CURE+ is a gap filling glue that dries in 5-15 sec.


Specs

  • Hobbylinc Product Number: 107

Includes

1oz bottle of insta-cure +


Requirements & Suggestions

← Swipe To View More →

Product Rank


Reviews

  
 
"The standard for gap-filling CA glues"
scott
This stuff is great, plain and simple. It just works, filling in gaps and bonding a variety of things together. Especially for rocketry, the gap-filling aspect is very useful. For smaller rockets, this alone will usually hold fins in place (though I'd still encourage at least wood glue fillets). For larger rockets, a few dots along the root edge of a fin will hold it in place against the body tube or motor mount tube, after which you can deploy your favorite epoxy for filleting the fins, inside and out.

 
"Not for clear parts"
Dr.Glueblob (Phoenix AZ)
Two tips here.. Do NOT use Insta-Cure (Or any other CA glue) to attach aircraft canopies or model car windshields. The glue will cause fogging of clear parts as it dries. ..And, unless you are doing a lot of CA gluing at once, buy the product in the smaller sizes. Superglue tends to harden in the bottle quickly after it's opened. I've lost much more to waste than I saved buying more than an ounce or so at a time. Happy modeling!

 
"Insta Cure Gap Filling Cyanoacrylate Glue"
mooniemac2000
This is CA glue, an extremely strong adhesive. This glue has a high viscosity so it flows slower. This glue is great because it does not leave any noticeable residue. Back in my rookie days in modeling, I messed up when I used nail glue, which also has CA, but left CA residue on the clear part. That makes this CA glue suitable for modeling.

Information

Cyanoacrylates (CAs) have become the adhesive of choice for most hobby and household applications. High quality CAs such as INSTA-CURE, when used properly, form bonds that in many cases are stronger than the material that is being adhered. INSTA-CURE is a highly refined CA which, combined with its freshness, gives a guaranteed 2 year shelf life. CAs are reactive monomers that chemically link (polymerize) when pressed into a thin film. The very thin layer of water moisture present on most surfaces acts as an alkali, or weak base, which is the catalyst that results in bonding; however, the presence of detectable amounts of water usually degrades the performance of CAs.

Others Also Ordererd

← Swipe To View More →